Important Safety Instructions; To Prevent The Risk Of Electrical Shock - Barco DP2K-20CLP Safety Manual

1.2

Important safety instructions

To prevent the risk of electrical shock

• This projector should be operated from an AC power source. Ensure that the mains voltage and capacity matches the projector
electrical ratings. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the
grounding.
• Installation according to the local electrical code and regulations by qualified technical personnel only.
• This product is equipped with a three-terminal barrier strip for the connection of a mono phase line with a separate earth ground
PE. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the grounding.
• The cross-sectional area of the conductors in the power supply cord shall be not less than 4 mm
• The electronics of the projector must be powered either from a suitable UPS unit or from the power outlet socket (UPS OUTLET)
provided on the projector. For that reason an adapted short power cord (2-pole 3-wire grounding) is added to the projector
accessories to loop through the power.
• The cross-sectional area of the UPS inlet cord shall be not less than 0.75 mm² or AWG 18.
• The provided power output socket (UPS OUTLET) on the projector may only be used to provide power to the projector elec-
tronics. Never connect other devices to this power output socket.
• The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general disconnect switch(es)
to switch off the complete installation.
• Disconnect the power to the projector mains terminals and unplug the power cord at UPS INLET for removal of all power from
the projector.
• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.
• Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it has been examined
and approved for operation by a qualified service technician.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
• Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short
circuit parts that could result in a risk of fire or electrical shock.
• Do not expose this projector to rain or moisture.
• Do not immerse or expose this projector in water or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
• Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the manufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect media and communication cables. This will prevent damage
to the projector due to lightning and AC power-line surges.
To prevent fire hazard
• Do not place flammable or combustible materials near the projector!
• Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclusion zone" around all external
surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less
than 40 cm (16") for all DLP Cinema projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the
projector or the lens with any material while the projector is in operation. Keep flammable and combustible materials away from
the projector at all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light.
Never expose the projector to rain or moisture. In the event of fire, use sand, CO
water on an electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always
insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this
projector.
• Ensure no miss alignment can occur. Prolonged long time exposure of black wooden walls at close distance (< 20cm) can
represent a fire risk. After alignment the projector shall be securely mounted to the pedestal.
• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Projection rooms must be well ventilated or cooled in order to avoid build-up of heat. It is necessary to vent hot exhaust air from
projector and cooler to the outside of the building.
• Let the projector cool completely before storing. Remove cord from the projector when storing.
R5906714 DP2K CLP SERIES 09/05/2016
2 or AWG 10.
or dry powder fire extinguishers. Never use
2
1. Safety
3