Charder MS2500 User Manual

Charder MS2500 User Manual

Medical scale
Hide thumbs Also See for MS2500:

Advertisement

Manufacturer's Declaration of Conformity
This product has been manufactured in accordance with
the harmonized European standards, following the
provisions of the below stated directives:
93/42/EEC
2007/47/EC
Medical Device Directive
2014/31/EU
Non-automatic Weighing Instruments
Directive
Please see separate document showing on sticker of device for
above CE marking.
Authorized EU Representative:
Manufactured by:
Charder Electronic Co., Ltd.
No.103, Guozhong Rd., Dali Dist.,
Taichung City 412 ,Taiwan (R.O.C.)
FDA no.: D051882
IN-1045 [8044J] 04/2016 IN-8654
as
amended
35
by
Please keep the instruction manual at hand all the time for future reference.
MS2500 / MS2501
Medical Scale
USER MANUAL
0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MS2500 and is the answer not in the manual?

Questions and answers

Summary of Contents for Charder MS2500

  • Page 1 Directive Please see separate document showing on sticker of device for above CE marking. Authorized EU Representative: Manufactured by: Charder Electronic Co., Ltd. No.103, Guozhong Rd., Dali Dist., Taichung City 412 ,Taiwan (R.O.C.) MS2500 / MS2501 FDA no.: D051882 Medical Scale USER MANUAL Please keep the instruction manual at hand all the time for future reference.
  • Page 2: Table Of Contents

    Wrong internal wiring or wire broken TABLE OF CONTENTS In case of the following defective mode occurs, it is suggested to contact your nearest Authorized Dealer for further technician service & repair: PREFACE ..................2 1. POWER switch-on failure : GENERAL INFORMATION ..............
  • Page 3: Preface

    Our warranty service program includes the following: please contact your CHARDER MEDICAL service partner, or visit us 1. Technician repair service under warranty or at a service maintenance charge depending on the workmanship for the on the Internet at www.chardermedical.com...
  • Page 4: Enviromental

    ERROR MESSAGE If you have any question, contact your local CHARDER MEDICAL service partner. Low battery : This warning shows that the voltage ENVIROMENTAL of battery is too low to use. Please All batteries contain toxic compounds; disposal of batteries replace new battries or plug the AC adaptor for operation.
  • Page 5: Weighing Operation

    CHARDER MEDICAL’s scope of responsibility, CHARDER shall have the right to either repair the fault or supply a replacement unit. Replaced parts shall be the property of CHARDER. Should the fault repairs or replacement delivery not be successful, the statutory provisions shall be valid.
  • Page 6: Disposing Of The Scale

    If operating, climatic or any other influences lead to a major change in conditions or material quality, the treaty for perfect unit functioning shall be rendered null and void. If CHARDER provides is displayed on the LCD, you should charge scale with exclusive adaptor for MS 2500 and individual warranty, this means that the unit supplied will be free of faults for the length of the warranty period.
  • Page 7 To return to the normal weighing mode when the scale plate is commissioning, even if you are unloaded, press the PRE-Tare key shortly again. This will also result already familiar with Charder scales. in disappearing the small arrow pointing the „PRE-TARE” symbol. +60°C...
  • Page 8: Emc Guidance And Manufacturer's Declaration

    EMC guidance and manufacturer's declaration pointing the ”PRE-TARE” symbol on the display. The value used as the last one will be displayed. If a different value is required, a new weight value can be entered with the numerical Guidance and manufacturer’s declaration-electromagnetic emissions keypad.
  • Page 9 BMI value during weighing. IEC 61000-4-2 If floors are covered with (For MS2500 model, press [HOLD/BMI] key to confirm changes synthetic material, the relative humidity should of height value), and the BMI index will be displayed on the LCD be at least 30% screen during weighing.)
  • Page 10 Wait until the weighing value is stable. Then press the BMI key watts (W) according to the (For MS2500 model, long press [HOLD/BMI] key for 3 seconds transmitter manufacturer and d is to enter BMI mode) the recommended separation distance in metres (m).
  • Page 11 USING SCALE – Key Functions WEIGHING Switch on the scale with the [ON/OFF] key. The diagnostic scale self-check is performed and then the software version is displayed. The scale is ready for weighing when the „0,00 kg” weight display is shown. Direction: The [→0←] key makes it possible to zero the scale if necessary and at any time.
  • Page 12 SETTING UP YOUR DEVICE STEP BY STEP Recommended separation distance between portable and mobile RF For Example: Setup 180s AUTO-OFF time and Buzzer OFF communications equipment and the MEDICAL SCALE The MEDICAL SCALE MS2501 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
  • Page 13: Specification

    3 seconds. TARE Transport / Storage - 20°C … + 60°C Temp. & Humidity 10% - 95% RH MS2500 MS2500:ON/OFF, UNIT, HOLD/BMI, TARE MS2501 4key OIML CIII ON/OFF, (zero), HOLD , TARE MS2501 20key OIML CIII Key Functions ON/OFF,...
  • Page 14: Medical Scale Models Approval List

    HM-80P , HM-80M , HM-200P , HM-200PW , Remove weight and press HOLD again to disable hold function. Measurement HM101M, HM110M, HM201M, HM230M, HOLD/BMI : To lock weight and BMI function. [MS2500] HM202P PRESET TARE: To set target weight for tare before starting measurement.
  • Page 15: Power Adaptor Standards

    KEY FUNCTIONS POWER ADAPTOR STANDARDS AMP VOLTAGE DRAWING NO.: CE APPROVED TYPE NO. TYPE MS2500 (NP-4444) / MODEL NO.: 9V DC 100mA AD-038A REV 007 D41W1090100-13/1 9V DC 100mA AD-0484 REV 001 D35W090100-23/1 9V DC 100mA AD-0484 REV 001 SP35-90100...
  • Page 16: Lcd Display

    LCD DISPLAY Step3. Fixing DP2701 indicator. PRE-TARE Indication Hold Indication NET WEIGHT Indication WEIGHT Indication BMI Indication Make sure DP2701 is well fixed on column Definitions Stable symbol: When user stands on scale and is stable. Minor weight: Weight under zero. Zero symbol: Weight is at zero point.
  • Page 17: Assembly Instruction

    Fixing handrail and column with screw. ASSEMBLY INSTRUCTION Step1. Fixing first handrail column on platform (figure1) Tighten screws first Fixing second handrail column on platform (figure2) Attention : The screws to mount handrail must be tightly fixed...
  • Page 18 Fixing third handrail column on platform (figure3) Step2.Fixing handrail. Fixing third handrail column on platform (figure4) Assemble handrail and column. Tighten upper screws first Tighten side screws after...

This manual is also suitable for:

Ms2501

Table of Contents