Safety Instructions - Flex LW 1202 Original Operating Instructions

Safety instructions

t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
Combined safety instructions for
grinding, sanding and polishing:
 This electric power tool must be used
as a grinder, sander and polisher.
Observe all safety information, instruc-
tions, diagrams and data which you
receive with the power tool. If you do not
observe the following instructions, an
electric shock, fire and/or serious injuries
may occur.
 This electric power tool is not suitable
for use with wire brushes and for cut-off
grinding. If the electric power tool is not
used as intended, the user may be
exposed to hazards and may be injured.
 Never use accessories which the manu-
facturer did not intend or recommend
especially for this electric power tool.
Just because you can attach the acces-
sory to your electric power tool does not
guarantee safe use.
 The permitted speed of the insertion tool
must be at least as high as the maximum
speed indicated on the electric power tool.
An accessory which rotates faster than
permitted may shatter and fly off.
 Outer diameter and thickness of the inser-
tion tool must correspond to the dimen-
sions of the electric power tool.
Incorrectly measured insertion tools
cannot be adequately shielded or
controlled.
 Grinding discs, flanges, sanding pads
or other accessories must fit exactly
on the grinding spindle of your electric
power tool. Insertion tools, which do not
fit exactly on the grinding spindle of the
electric power tool, rotate unevenly,
vibrate violently and may result in loss
of control.
14
 Do not use any damaged insertion tools.
Before use, always check insertion tools
for splinters and cracks, sanding pad
for cracks, wear and severe abrasion,
wire brushes for loose or broken wires.
If the electric power tool or the insertion
tool is dropped, check for damage
or use an undamaged insertion tool.
When you have checked and inserted
the tool, ensure that you and anybody
in the vicinity remain outside the plane
of the rotating insertion tool and leave
the power tool running for one minute
at maximum speed. Damaged insertion
tools usually break during this test time.
 Wear personal protective equipment.
Depending on the application, wear full
face protection, eye protection or goggles.
If appropriate, wear a dust mask, hearing
protection, protective gloves and/or
a special apron which protect you from
small sanding and material particles.
You should protect your eyes from foreign
objects which are ejected for different
applications. Dust and respirator masks
must filter the dust which is generated
by the power tool for the particular appli-
cation. If you are exposed to loud noise
for a prolonged period, you may suffer
hearing loss.
 Ensure that other persons are situated
at a safe distance from the work area.
Anyone who enters the work area must
wear personal protective equipment.
Fragments of the workpiece or broken
insertion tools may fly off and cause inju-
ries even outside the direct working area.
 If the insertion tool is at risk of coming into
contact with concealed power cables
or the power cord itself, hold the power
tool by the insulated grip surfaces only.
Contact with a live cable may also cause
metal parts of the appliance to become
live and result in an electric shock.
 Keep the power cord away from rotating
insertion tools. If you lose control of the
appliance, the power cord could be seve-
red or become caught and your hand or
arm may strike the rotating insertion tool.
Wet stone grinder