Front View Reset Button Power LED Power Button HDD LED Rear View Expansion slot DVI-I (DVI-D signal) PS/2 Mouse/KB COM 1 LAN 1-2 Line-out Line-in/Surround HDMI USB 3.0 Mic-in/Center+Subwoofer USB 2.0 DVI-I...
Key Features DT122-CR ® 3rd/2nd Generation Intel Core processors PROCESSOR ® CHIPSET Intel QM77 2 LAN ports 1 COM port DISPLAYS 2 DVI-I (1 DVI-D Signal), 1 HDMI 4 Type A USB 3.0/2.0/1.1 ports 2 Type A USB 2.0/1.1 ports 2 Type A USB 2.0/1.1 ports (optional)
Removing the Chassis Cover 1. Make sure the system and all other peripheral devices connected to it has been powered-off. 2. Disconnect all power cords and cables. 3. The 4 mounting screws on the sides of the system are used to secure the cover to the chassis. Remove these screws and then put them in a safe place for later use.
Page 5
4. After removing the mounting screws, slide the cover backwards. Slide the Cover Backward 5. The DIMM sockets and SATA drive bay are readily accessible after removing the chassis cover. SODIMM socket 2.5"/3.5" SATA drive bay...
Installing a 2.5" or 3.5" SATA Drive lnstalling a 2.5" SATA Drive 1. Remove the 4 mounting screws that secure the drive bay to the system. Mounting screw Drive bay Mounting screw 2. Turn to the other side of the drive bay and remove the 4 mounting screws that secure the HDD brackets to the drive bay.
Page 7
3. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket and then use the provided mounting screws to secure the drive in place. Mounting screw SATA drive Mounting screw HDD bracket...
Page 8
4. Turn to the other side of the drive bay. Use the provided mounting screws from step 2 to secure the SATA drive bay assembly onto the drive bay. Drive bay Mounting screw Mounting screw 5. Place the SATA drive bay assembly into the chassis. Secure the SATA drive bay with the mounting screws you removed in step 1.
Page 9
6. Connect the SATA data cable and SATA power cable to the connectors on the SATA drive. SATA power SATA data cable cable...
Page 10
lnstalling a 3.5" SATA Drive 1. Remove the 4 mounting screws that secure the drive bay to the system. Mounting screw Drive bay Mounting screw 2. Insert the spacer into the anti-shock bumper. You will fi nd the spacers in the HDD drive bay kit that comes with the DT122 package.
Page 11
4. Use the provided mounting screws to secure the SATA drive onto the drive bay. Mounting screw Mounting screw Drive bay 5. Place the drive bay into the chassis. Secure the drive bay with the mounting screws you removed in step 1. Mounting screw Mounting screw 6.
Page 12
Installing the PCI or PCIe x16 Expansion Card Important: When inserting the riser card, please select a card within 175mm (as shown on the next picture). 1. The PCIe x16 slot on the motherboard is used to in- sert a TS200-1P and TS200-1E riser card. To install the expansion card, you need to remove the mounting bracket and the mounting screw that secure the bracket to the chassis and then remove the brack-...
Page 14
2. Insert the Expansion card with a bracket into the PCI or PCIe x16 slot that is on the riser card. Replace the screw you removed in step 1 to secure the bracket in place. Bracket Mounting bracket and mounting screw Expansion card Rear view...
Mounting Options Wall mount There are 2 types of wall mount brackets: • Type A • Type B Type A wall mount kit include: • 2 type A wall mount brackets 1. If the mounting screw has been previously attached to the top cover of the system, please remove them fi...
Page 16
2. At the sides of the system, use the mounting screws removed in step 1 to secure the wall mount brackets on each side of the system. Wall mount bracket Wall mount bracket Mounting screw 319.00 4-#6-32 Ø4.00 Ø8.50 Ø5.00 Ø3.60 300.00...
Page 17
Type B wall mount kit include: • 2 type B wall mount brackets • Bracket screws 1. The 4 mounting holes on the sides of the system are used to mount the type B wall mount bracket. 2. Use the provided mounting screws to secure the type B wall mount brackets on each side of the system.