At+Mmid; At+Idfir; At+Ideve - Jinan USR IOT Technology WIFI232-A User Manual

Notes: AT+FUDLX is F-Setting, means restore to factory setting will not affect this command.
5.2.2.2.36 AT+ MMID
5.2.2.2.36 5.2.2.2.36 5.2.2.2.36 AT+ AT+

AT+MMID

MMID MMID
�
Function: Set/Query Device ID;
�
Format:
�
Query Operation
AT+ AT+ AT+ AT+MMID MMID MMID<CR> MMID <CR> <CR> <CR>
+ok=<time><CR>< +ok=<time><CR>< +ok=<time><CR>< +ok=<time><CR>< LF
�
Set Operation
AT+ AT+ MMID MMID =<time><CR> =<time><CR>
AT+ AT+ MMID MMID=<time><CR> =<time><CR>
+ok<CR>< +ok<CR>< LF LF
+ok<CR>< +ok<CR>< LF LF ><CR><
�
Parameters:
�
ID: device id(0~65535)
After USR-WIFI232-A/B/C module boots up again, the setting will be effective.
5.2.2.2.37 5.2.2.2.37 5.2.2.2.37 5.2.2.2.37

AT+IDFIR

AT+IDFIR AT+IDFIR AT+IDFIR
� Function: Enable/Disable "Send an ID when module connection is established" function;
� Format:
� Query Operation
AT+ AT+ IDFIR IDFIR <CR> <CR>
AT+IDFIR AT+ IDFIR<CR> <CR>
+ok=<on/off><CR><LF><CR><LF> +ok=<on/off><CR><LF><CR><LF>
+ok=<on/off><CR><LF><CR><LF> +ok=<on/off><CR><LF><CR><LF>
�
Set Operation
AT+ IDFIR =<on/off><CR>
AT+ AT+ AT+IDFIR IDFIR=<on/off><CR> IDFIR =<on/off><CR> =<on/off><CR>
+ok<CR><LF><CR><LF>
+ok<CR><LF><CR><LF> +ok<CR><LF><CR><LF> +ok<CR><LF><CR><LF>
�
Parameters:
�
On/off: Enable or Disable "Send an ID when module connection is established"
function
�
�
5.2.2.2.38 5.2.2.2.38

AT+IDEVE

AT+IDEVE
5.2.2.2.38 5.2.2.2.38 AT+IDEVE AT+IDEVE
�
Function: Enable/Disable Every time to send data to send ID function;
�
Format:
�
Query Operation
AT+ AT+ AT+IDEVE AT+ IDEVE IDEVE<CR> IDEVE
+ok=<on/off><CR><LF><CR><LF> +ok=<on/off><CR><LF><CR><LF> +ok=<on/off><CR><LF><CR><LF> +ok=<on/off><CR><LF><CR><LF>
� Set Operation
AT+ AT+ AT+IDEVE AT+ IDEVE IDEVE=<on/off><CR> IDEVE
+ok<CR><LF><CR><LF> +ok<CR><LF><CR><LF> +ok<CR><LF><CR><LF> +ok<CR><LF><CR><LF>
�
Parameters:
�
On/off: Enable or Disable Every time to send data to send ID function
�
�
Note: The ID function requires that the server carries out corresponding processing.In front of the
data when module connected to the server with two bytes of ID (ID the range is 0 ~ 65535, the
high byte before,
Jinan USR IOT Technology Limited
USR-WIFI232-A/B/C User Manual
LF ><CR>< LF LF ><CR>< ><CR>< ><CR>< LF LF LF LF > > > >
><CR>< ><CR>< LF LF LF > > > >
><CR>< LF
On, enable "Send an ID when module connection is established" function;
Off, disable "Send an ID when module connection is established" function;
<CR> <CR> <CR>
=<on/off><CR> =<on/off><CR> =<on/off><CR>
On, enable Every time to send data to send ID function;
Off, disable Every time to send data to send ID function;
and the low byte
Page 68 of 93
behind) plus two
http://www.usriot.com
bytes ID radix-minus-one
tec@usr.cn