Related Manuals for SHOWTEC Kanjo Spot 60
Summary of Contents for SHOWTEC Kanjo Spot 60
- Page 1 MANUAL ENGLISH Kanjo Spot 60 Ordercode: 45011 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Kanjo Spot 60 Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................6 Claims ....................................6 Description of the device ..............................7 Features ..................................7 Overview .................................. -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Kanjo Spot 60 • IEC power cable (1,5 m) •... - Page 4 • If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
Kanjo Spot 60 • This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth. • During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective. -
Page 6: Connection With The Mains
Kanjo Spot 60 The Kanjo can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug. -
Page 7: Return Procedure
Kanjo Spot 60 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. -
Page 8: Description Of The Device
Kanjo Spot 60 Description of the device Features The Kanjo Spot 60 is an ultra-compact moving head, equipped with a 60W LED Light source. The Kanjo Spot 60 is the ideal solution for small clubs and mobile DJs. Compact size •... -
Page 9: Frontside
Kanjo Spot 60 Frontside Fig. 02 01) 60W LED source 02) 4-digit LED Display + control buttons 03) Built-in microphone Backside Fig. 03 04) 3-pin DMX signal connector IN 05) 3-pin DMX signal connector OUT 06) Fuse F3AL/250V 07) IEC power connector 100-240V... -
Page 10: Installation
Kanjo Spot 60 Installation Remove all packing materials from the Kanjo Spot 60. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. -
Page 11: Multiple Kanjos (Master/Slave Control)
Kanjo Spot 60 Multiple Kanjos (Master/Slave control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Use a 3-pin XLR cable to connect the Kanjo. The pins: Earth Signal - Signal + 03) Link the units as shown in fig. -
Page 12: Multiple Kanjos (Dmx Control)
Kanjo Spot 60 Multiple Kanjos (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Kanjos and other devices. -
Page 13: Fixture Linking
Kanjo Spot 60 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 14: Control Panel
Kanjo Spot 60 The Kanjo Spot 60 can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel A) LED display MENU button C) UP button D) DOWN button ENTER button Fig. 06 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. -
Page 15: Menu Overview
Kanjo Spot 60 Menu Overview Ordercode: 45011... -
Page 16: Main Menu Options
Kanjo Spot 60 Main Menu Options DMX-512 mode Pan/Tilt reverse mode Channel mode Master/Slave mode Sound-controlled mode LED display continuous ON/OFF LED display reverse mode Reset Manual mode Manual DMX adjustment mode 1. DMX-512 mode 01) While in the main menu, press the UP/DOWN buttons until the display shows 02) Press the ENTER button to open the menu. -
Page 17: Master (Auto)/Slave Mode
Kanjo Spot 60 4. Master (Auto)/Slave mode 01) While in the main menu, press the UP/DOWN buttons until the display shows 02) Press the ENTER button to enter the menu. 03) Press the UP/DOWN buttons to choose one of the two modes:... -
Page 18: Manual Mode
Kanjo Spot 60 9. Manual mode 01) While in the main menu, press the UP/DOWN buttons until the display shows 02) Press the ENTER button to enter the menu. 03) Press the UP/DOWN buttons to choose between the two options:... -
Page 19: Dmx Channels
Kanjo Spot 60 DMX Channels 8 channels Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. -
Page 20: Channels
Kanjo Spot 60 Channel 8 – Functions 0-93 Not functional Reset Restore factory settings 96-255 Sound-controlled mode 10 channels Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). -
Page 21: Maintenance
04) The electric power supply cables must not show any damages or material fatigue. The Kanjo Spot 60 requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth. -
Page 22: Static Gobo Wheel And Color Wheel
Kanjo Spot 60 Static Gobo wheel and Color wheel Static Gobo Wheel Fig. 07 Color wheel Fig. 08 Ordercode: 45011... -
Page 23: Troubleshooting
Suspect three potential problem areas as: the power supply, the LEDs, the fuse. 01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Kanjo to your Showtec dealer. 03) The fuse. Replace the fuse. See page 20 for replacing the fuse. -
Page 24: No Response To Dmx
Kanjo Spot 60 No Response to DMX Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power. -
Page 25: Product Specifications
Kanjo Spot 60 Product Specifications Model: Showtec Kanjo Spot 60 Input Voltage: 100-240V AC, 60/50Hz Power consumption: 70W (full output) DMX linking: 30pcs Fuse: F3AL/250V Dimensions: 167 x 145 x 270 mm (LxWxH) Weight: 2,9 kg Operating and Programming: Signal pin OUT:... -
Page 26: Dimensions
Kanjo Spot 60 Dimensions Ordercode: 45011... -
Page 27: Notes
Kanjo Spot 60 Notes Ordercode: 45011... - Page 28 ©2015 Showtec...