Network Setup; Ip Address Sub-Menu; Proxy Sub-Menu; Mac Address Sub-Menu - Onkyo TX-NR1000 Instruction Manual

Network Setup

If using a broadband router (DHCP function), you need not perform "7. Network Setup" because the DHCP function
on the TX-NR1000/TX-NR5000E is defaulted to "Enable." When the DHCP function for the broadband router is set to
"Disable," network setup is required. In this case, you have to be knowledgeable about the network.
DHCP (Dynamic Host Configuration Protocol) and Auto IP are the mechanisms that automatically perform network
settings such as IP address on a network device such as the TX-NR1000/TX-NR5000E, a PC, and a broadband router.
DNS (Domain Name System) is the mechanism that converts a domain name, such as "www.onkyo.com/jp/" used to
browse a homepage, to an IP address such as "210.199.170.69" used in actual communications.

IP Address Sub-menu

a. DHCP Settings
Specify whether or not to set DHCP automatically.
Enable (Default): Enables the DHCP function.
Disable: Disables the DHCP function.
b. IP Address
Specify if "Disable" is selected in "a. DHCP Settings."
When an xDSL modem or a terminal adapter is
connected directly to the TX-NR1000/TX-NR5000E,
enter the IP address provided by your ISP. The IP
address to be entered must be in the following format.
You cannot use the net audio function with an IP
address that is not in the following format.
CLASS A: 10.0.0.0–10.255.255.255
CLASS B: 172.16.0.0–172.31.255.255
CLASS C: 192.168.0.0–192.168.255.255
c. SUBNET Mask
Specify if "Disable" is selected in "a. DHCP Settings."
When an xDSL modem or a terminal adapter is
connected directly to the TX-NR1000/TX-NR5000E,
enter the subnet mask provided by your ISP. The subnet
mask is usually "255.255.255.0."
d. Gateway
Specify if "Disable" is selected in "a. DHCP Settings."
When an xDSL modem or a terminal adapter is
connected directly to the TX-NR1000/TX-NR5000E,
enter the gateway address provided by your ISP.
e. DNS Server 1, DNS Server 2
Specify if "Disable" is selected in "a. DHCP Settings."
When an xDSL modem or a terminal adapter is
connected directly to the TX-NR1000/TX-NR5000E,
enter the DNS address provided by your ISP. If
connected to a gateway (router), enter the IP address of
the gateway.
When you are informed of a single DNS address, enter
the address into "e. 1st." If informed of two or more,
enter one into "f. 2nd."

Proxy Sub-menu

Specify when connecting to the Internet via a proxy
server.
a. Proxy Server
Some ISPs (Internet service providers) use a proxy
server to connect to the Internet. In this case, follow the
written instructions from the provider to set the proxy.
Enable: Enables the proxy server function.
Disable (Default): Disables the proxy server function.
b. Proxy URL Input
Enter the domain name of the proxy server. When
"Disable" is set for "a. Proxy Server," selecting this
item and pressing the [ENTER] button will put the
TX-NR1000/TX-NR5000E into the character entry
mode. Press the [ ]/[ ]/[ ]/[
numerics, and then press the [ENTER] button. When all
numerics are entered, exit from the character entry
mode.
c. Proxy Port
Enter the port No. of the proxy server. When "Disable"
is set for "a. Proxy Server," selecting this item and
pressing the [ENTER] button will put the TX-NR1000/
TX-NR5000E into the character entry mode. Press the
[ ]/[ ]/[ ]/[ ] buttons to select numerics, and then
press the [ENTER] button. When all numerics are
entered, exit from the character entry mode.
Note:
When the settings are complete, press the [RETURN]
button to return to the Network Setup menu. Use the
] buttons to select " → Save Settings," and then
[ ]/[
press the [ ] button to save settings. After setting,
saving data will take a few seconds. While saving data,
be sure not to turn off the power, otherwise the data will
be lost.

MAC Address Sub-menu

a. MAC Address
Confirm the MAC address of your PC. You cannot
change the MAC address.
] buttons to select
121