Connecting Antennas; Connecting The Indoor Fm Antenna; Connecting The Am Loop Antenna - Onkyo TX-NR1000 Instruction Manual

Connecting Antennas

This chapter explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
FM antenna connector
AM antenna push terminals
DIGITAL IN DIGITAL IN E MULTI F AUDIO IN
C D - CH
OPTICAL COAXIAL IN 1 R L
FR FL
1 1 PH
SUB C
2 2
GND
SR SL R L
"Net-Tune" 1
is a trademark of 3 3
Onkyo Corporation.
SBR SBL
4 4 2
FR FL
ETHERNET
5 5 3
( Net-Tune )
SUB C
1
6 6
SR SL
1 1 2
SBR SBL
2 2 3
R L
OUT
MULTI
- CH
A B C D IN 2 F
SURR R SURR BACK R ( ASSIGNABLE ) FRONT R
PRE OUT A
FRONT SURR SURR
BACK
A
L
R
B
SUB SUB
CENTER FRONT R (BTL)
WOOFER WOOFER
PRE
OUT B

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.
1
Attach the FM antenna, as shown.
I USA and Canadian Model
FM
Insert the plug fully
75
into the socket.
I Other Models
FM
75
Insert the plug fully
into the socket
Once your TX-NR1000/TX-NR5000E is ready
for use, you'll need to tune into an FM radio
station and adjust the position of the FM antenna
to achieve the best possible reception.
2 Use thumbtacks or something similar to
fix the FM antenna into position.
Caution: Be careful that you don't injure
yourself when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead.
28
G H S VIDEO VIDEO I COMPONENT J K L
VIDEO
R L IN IN IN 1
IN 2 RS 232
COMPONENT VIDEO ANTENNA HDMI
IN 4
4 1 Y
Y
IN 1
5 2 P B
P B
REMOTE
HDMI, the HDMI logo 12V
6 CONTROL
3 P R is a trademark
FM TRIGGER
or registered
75 trademarks of HDMI OUT
IN 3
OUT 1 Licensing LLC. A
P
R 200mA MAX.
7 4 Y IN 2
B 100mA MAX.
C
OUT 2 100mA MAX.
8 5 P B
Y D 100mA MAX.
AM E
100mA MAX.
9
6 P R
P B
MAIN
4 1 3
ZONE 2
P R
5 2 4
R L ZONE 3
OUT OUT OUT OUT
G S VIDEO VIDEO VIDEO S VIDEO
IN OUT
H I J K L
IR
CENTER FRONT L SURR BACK L ( ASSIGNABLE ) SURR L
( SINGLE )
SPEAKERS A
AC INLET
AC OUTLET
AC 120V 60Hz
SWITCHED
120W 1A MAX.
SPEAKERS B
FRONT L (BTL)
UDC/UDT MODEL NO. TX-NR 1000
Thumbtacks, etc.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use
only.
1 Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna's wires are not polarity sensitive, so
they can be connected in either terminal)
Make sure that the wires are attached securely
and that the push terminals are gripping the bare
wires, not the insulation.
Push
Insert wire
AM
Once your TX-NR1000/TX-NR5000E is ready
for use, you'll need to tune into an AM radio
station and adjust the position of the AM antenna
to achieve the best possible reception. Keep the
antenna as far away as possible from your
TX-NR1000/TX-NR5000E, TV, speaker cables,
and power cords.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using a commercially
available outdoor AM antenna.
Release