Download Table of Contents
Share
Print this page
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Projector
  5. NP3200
  6. User manual

NEC NP3200 User Manual

Hide thumbs Also See for NP3200:

Advertisement

Quick Links

Download this manual
Table of Contents

LCD Projector

NP3200/NP2200/NP1200
User's Manual
The NP3200 is not distributed in North America.
Downloaded From projector-manual.com NEC Manuals

Advertisement

Table of Contents
loading

Related Manuals for NEC NP3200

Summary of Contents for NEC NP3200

  • Page 1: Lcd Projector

    LCD Projector NP3200/NP2200/NP1200 User’s Manual The NP3200 is not distributed in North America. Downloaded From projector-manual.com NEC Manuals...
  • Page 2 (3) Great care has been taken in the preparation of this manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.

  • Page 3: Safety Cautions

    Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC NP3200/NP2200/NP1200 projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
  • Page 4 The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 5: Important Safeguards

    Place the projector in a horizontal position The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. 10° Downloaded From projector-manual.com NEC Manuals...
  • Page 6 • Turn off the projector and unplug the power cable if the projector is not to be used for an extended period of time. • When using a LAN cable: For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage. Downloaded From projector-manual.com NEC Manuals...

  • Page 7: Remote Control Precautions

    CAUTION: When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out. Downloaded From projector-manual.com NEC Manuals...
  • Page 8 [ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features. Downloaded From projector-manual.com NEC Manuals...

  • Page 9: Table Of Contents

    2. Installation and Connections ..............12  Setting Up the Screen and the Projector ..............12 Selecting a Location [NP3200/NP2200/NP1200]........... 12  Making Connections ....................13 Connecting Your PC or Macintosh Computer ............13 Connecting an External Monitor ................16 Connecting Your DVD Player with Component Output ...........
  • Page 10  Screen Size and Projection Distance ................92 [NP3200/NP2200/NP1200] ..................92  Pin Assignments of D-Sub COMPUTER 1 Input Connector ........94 Mini D-Sub 15 Pin Connector ................94  Compatible Input Signal List ..................95 viii Downloaded From projector-manual.com NEC Manuals...
  • Page 11 7 PC Control Codes and Cable Connection ..............96 PC Control Codes ....................96 Cable Connection ....................97 PC Control Connector (D-SUB 9P) ................ 97 8 Troubleshooting Check List ..................98 9 TravelCare Guide ....................... 100 Downloaded From projector-manual.com NEC Manuals...

  • Page 12: Important Information

    • Security sticker For North America only (24L67991) Registration card Limited warranty • Anti-theft screw for lens × 1 (24V00841) For customers in Europe: You will find our current valid Guarantee Policy on our Web Site: www.nec-display-solutions.com Downloaded From projector-manual.com NEC Manuals...

  • Page 13: Introduction To The Projector

    PC control port (D-Sub 9 Pin) and LAN support. With input and output flexibility, long lamp life and a full function remote, the NP3200/NP2200/NP1200 lets you enjoy larger than life viewing from a com- pact and easy to setup and use projector.

  • Page 14: About This User's Manual

    The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find an overview. If the section doesn’t apply, you can skip it. Downloaded From projector-manual.com NEC Manuals...

  • Page 15: Part Names Of The Projector

    Main Power switch, the POW- and plug the other end into an active wall outlet. ER indicator turns orange and the projector is in standby (→ page 20) mode. (→ page 21) Downloaded From projector-manual.com NEC Manuals...

  • Page 16: Bottom

    When moving the projector or when it is not in use, cover the lens with the lens cap. NOTE: To stand the projector on its end, do so by holding the cabinet, not by holding the carrying handle. Doing so can cause damage to the carrying handle. Lock Downloaded From projector-manual.com NEC Manuals...
  • Page 17 3. Press down the left and right locks to set the carrying handle in place. • To place back the carrying handle, press up the left and right locks and pull down the carrying handle. Downloaded From projector-manual.com NEC Manuals...

  • Page 18: Top Features

    9.  /  Volume Buttons ( ) (→ page 3. STATUS Indicator (→ page 21, 31, 86) 10. ENTER Button (→ page 50) 4. LAMP Indicator (→ page 79, 86) 11. EXIT Button (→ page 50) Downloaded From projector-manual.com NEC Manuals...

  • Page 19: Terminal Panel Features

    PC Control (HDCP compatible) (→ page 15) Utility Pro 4 contained on the supplied NEC Projec- tor CD-ROM. To do so you must first have PC Con- AUDIO IN (Stereo Mini Jack) (→ page 15) trol Utility Pro 4 installed on your PC (→...

  • Page 20: Part Names Of The Remote Control

    29. HELP Button (not available on this series of projectors) (→ page 74) * The PAGE /, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse receiver (NP01MR) is connected with your computer. Downloaded From projector-manual.com NEC Manuals...

  • Page 21: Battery Installation

    • The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector. Downloaded From projector-manual.com NEC Manuals...

  • Page 22: Remote Control Precautions

    • Ensure that you have the batteries’ polarity (+/−) aligned correctly. • Do not use new and old batteries together, or use different types of batteries together. • Dispose of used batteries according to your local regulations. Downloaded From projector-manual.com NEC Manuals...

  • Page 23: Installation And Connections

     Setting Up the Screen and the Projector Selecting a Location [NP3200/NP2200/NP1200] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 30 inches (0.76 m) measured diagonally when the projector is roughly 41 inches (1.0 m) from the...

  • Page 24: Making Connections

    Usually, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.
  • Page 25 SOURCE button on the projector Input connector Button on the remote control cabinet COMPUTER 1 IN COMPUTER 1 (COMPUTER 1) COMPUTER 2 IN COMPUTER 2 (COMPUTER 2) COMPUTER 3 (DVI-D) IN COMPUTER 3 (COMPUTER 3) Downloaded From projector-manual.com NEC Manuals...
  • Page 26 With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC). Downloaded From projector-manual.com NEC Manuals...

  • Page 27: Connecting An External Monitor

    • When the projector is in standby condition, the MONITOR OUT connector outputs the video signal and the AUDIO OUT jack outputs the audio signal according to the setting of [OUT TERMINAL] in the menu. Choices are [LAST], [COMPUTER1], and [COMPUTER2]. ( → page 73) Downloaded From projector-manual.com NEC Manuals...

  • Page 28: Connecting Your Dvd Player With Component Output

    • Select the source name for its appropriate input connector after turning on the projector. SOURCE button on the projector Input connector Button on the remote control cabinet COMPUTER 1 IN COMPUTER 1 (COMPUTER 1) COMPUTER 2 IN COMPUTER 2 (COMPUTER 2) Downloaded From projector-manual.com NEC Manuals...

  • Page 29: Connecting Your Vcr

    NOTE: Refer to your VCR owner’s manual for more information about your equipment’s video output requirements. NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan converter. Downloaded From projector-manual.com NEC Manuals...

  • Page 30: Connecting To A Network

    2. Installation and Connections Connecting to a Network Example of LAN connection Example of wired LAN connection Server LAN cable (not supplied) NOTE: Use a Category 5 or higher LAN cable. Downloaded From projector-manual.com NEC Manuals...

  • Page 31: Connecting The Supplied Power Cable

    AC IN connector of the projector and (or) the prong plug of the power cable. NOTE: To turn off the AC power supply when the projector is powered on, use the Main Power Switch or a power strip equipped with a switch and a breaker. Downloaded From projector-manual.com NEC Manuals...

  • Page 32: Projecting An Image (Basic Operation)

    1 second. is removed. (→ page 86) NOTE: When no signal is available, the NEC logo, blue (default), or black screen will be displayed. When the projector displays the NEC logo, a blue or black screen, the projector will automatically switch to [ECO MODE].

  • Page 33: Note On Startup Screen (Menu Language Select Screen)

    Failing to do so could result in no power to the projector. (There will be no stand-by LED) Should this happen, unplug the power cable and plug it in again. Turn on the main power switch. Downloaded From projector-manual.com NEC Manuals...

  • Page 34: Selecting A Source

    TIP: When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER 1 IN or COMPUTER 2 IN input will power on the projector and simultaneously project the computer’s image. ([AUTO POWER ON(COMP1/2)] → page 73) Downloaded From projector-manual.com NEC Manuals...

  • Page 35: Adjusting The Picture Size And Position

    (→ page 27) (→ page 28) In the above drawings, cables are omitted for clarity. NOTE*: Adjust the throw angle (the height of an image) when the image position is higher than the lens shift adjustable range. Downloaded From projector-manual.com NEC Manuals...

  • Page 36: Adjusting The Position Of A Projected Image

    NOTE: Lens shift is not available with the NP01FL optional lens. The NP01FL should be used only for “zero degree” applica- tions. Desktop front projection Normal projection Position Vertical shift Max. 0.5V 0.5V 0.1H 0.1H Width of projected image Ceiling front projection Vertical shift Shift to left Shift to right Max. 0.5V Downloaded From projector-manual.com NEC Manuals...

  • Page 37: Adjusting The Focus (Focus Ring)

    • Rotate the focus ring to make focus adjustment. Focus ring Finely adjusting the size of an image (Zoom lever) • Rotate the zoom lever to adjust the image size on the screen. Zoom lever Downloaded From projector-manual.com NEC Manuals...

  • Page 38: Adjusting The Tilt Foot

    Do not use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry or hang (from the wall or ceiling) the projector can cause damage to the projector. Downloaded From projector-manual.com NEC Manuals...

  • Page 39: Correcting Keystone Distortion

    • The range of keystone correction is not the maximum tilt angle of projector. • The left and right (horizontal) keystone correction is not available. TIP: The changes can be saved with [KEYSTONE SAVE]. ( → page 63) Downloaded From projector-manual.com NEC Manuals...

  • Page 40: Adjusting From The Menu

    The menu will be closed. NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically. TIP: The changes can be saved with [KEYSTONE SAVE]. ( → page 63) Downloaded From projector-manual.com NEC Manuals...

  • Page 41: Optimizing An Rgb Image Automatically

    NOTE: • Volume control is not available with the  or  button when an image is enlarged by using the MAGNIFY (+) button or when the menu is displayed. Increase volume Decrease volume Downloaded From projector-manual.com NEC Manuals...

  • Page 42: Turning Off The Projector

    Preparation: Make sure that the main power is turned off. 1. Unplug the power cable. 2. Disconnect any other cables. 3. Retract adjustable tilt feet if extended. 4. Cover the lens with the lens cap. Downloaded From projector-manual.com NEC Manuals...

  • Page 43: Convenient Features

    Each time the MAGNIFY (−) button is pressed, the image is reduced. NOTE: • The image will be enlarged or reduced at the center of the screen. • Displaying the menu will cancel the current magnification. Downloaded From projector-manual.com NEC Manuals...

  • Page 44: Changing Eco Mode

    [ON] Select this mode to increase the lamp life (approx. Steady Green light LAMP POWER AUTO ADJ. 80% Brightness on NP3200 and approx. 88% STATUS Brightness on NP2200/NP1200). COMPUTER VIDEO S-VIDEO VIEWER To turn on the [ECO MODE], do the following: ＋...

  • Page 45: Checking Energy-Saving Effect [Carbon Meter]

    OECD publication “CO2 Emissions from Fuel Combustion, 2008 Edition”. • This formula will not apply to the power consumption which is not affected by whether [ECO MODE] is turned on or off. Downloaded From projector-manual.com NEC Manuals...

  • Page 46: Preventing The Unauthorized Use Of The Projector [Security]

    The [SECURITY KEYWORD] screen will be displayed. 6. Type in a combination of the four  buttons and press the ENTER button. NOTE: A keyword must be 4 to 10 digits in length. The [CONFIRM KEYWORD] screen will be displayed. Downloaded From projector-manual.com NEC Manuals...
  • Page 47 3. Type in the correct keyword and press the ENTER button. The projector will display an image. NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cable. Downloaded From projector-manual.com NEC Manuals...
  • Page 48 NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your re- quest code. Your request code is displayed in the Keyword Confirmation screen. In this example [K992-45L8-JNGJ-4XU9-1YAT- EEA2] is a request code. Downloaded From projector-manual.com NEC Manuals...

  • Page 49: Using The Optional Remote Mouse Receiver (Np01Mr)

    NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals. Downloaded From projector-manual.com NEC Manuals...
  • Page 50 CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button. TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user documentation or online help supplied with your computer. Downloaded From projector-manual.com NEC Manuals...

  • Page 51: Network Setting By Using An Http Browser

    IP address of the projector has been set in the “HOSTS” file of the computer being used. Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network setting by specifying http://pj.nec.co.jp/index.html...

  • Page 52: Network Settings

    TIP: Selecting [NETWORK SETTINGS] for [RESET] from the projector’s menu allows you to return the following items to the fac- tory default. [DHCP]: DISABLE [IP ADDRESS]: 192.168.0.10 [SUBNET MASK]: 255.255.255.0 [DEFAULT GATEWAY]: 192.168.0.1 * [DNS(PRIMARY)] and [DNS(SECONDARY)] will remain unchanged. Downloaded From projector-manual.com NEC Manuals...
  • Page 53 DOMAIN NAME �������������������������������Type in the domain name of the network connected to the projector� Up to 60 alphanu- meric characters can be used� If the domain name is unknown, type in the right side of @ in the sender’s address� Example: nec� com ALERT MAIL ������������������������������������Checking [ENABLE] will turn on the Alert Mail feature�...

  • Page 54: Using The Vga Signal Cable To Operate The Projector (Virtual Remote)

    9 Using the VGA Signal Cable to Operate the Projector (Virtual Remote) Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector’s power on or off and signal selection via the VGA signal cable.
  • Page 55 1 Insert the accompanying NEC Projector CD-ROM into your CD-ROM drive. The folders in NEC Projector CD-ROM will be displayed. If the folders are not displayed, right-click the CD/DVD drive icon in Windows’ “Computer” (or “My Computer”) and select “Open”.
  • Page 56 COMPUTER 1 IN → To wall outlet Main Power Switch AC Input Power cable (supplied) TIP: • When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed to navigate your connections. Downloaded From projector-manual.com NEC Manuals...
  • Page 57 • The Virtual Remote Tool screen (or Toolbar) can be displayed without displaying “Easy Setup” window. To do so, click to place a check mark for “ Do not use Easy Setup next time” on the screen at Step 6 in “Easy Setup”. Downloaded From projector-manual.com NEC Manuals...
  • Page 58 The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click “Start”. “All programs” or “Programs”. “NEC Projector User Supportware”. “Virtual Remote Tool”. and then “Virtual Remote Tool Help” in this order. The Help screen will be displayed.

  • Page 59: Controlling The Projector Over A Lan (Pc Control Utility Pro 4)

     Controlling the Projector over a LAN (PC Control Utility Pro 4) Using the utility software “PC Control Utility Pro 4” included on the companion NEC Projector CD-ROM, the projec- tor can be controlled from a computer over a LAN.
  • Page 60 Read “Virtual Remote Tool” as “PC Control Utility Pro 4” (→ page 45) Step 3: Start PC Control Utility Pro 4 Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” → “PC Control Utility Pro 4”.

  • Page 61: Using On-Screen Menu

    NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings. 8. Press the MENU button to close the menu. To return to the previous menu, press the EXIT button. Downloaded From projector-manual.com NEC Manuals...

  • Page 62: Menu Elements

    Key Lock symbol ����������������Indicates the [CONTROL PANEL LOCK] is enabled� Thermometer symbol ���������Indicates the [ECO MODE] is forcibly set to [ON] mode because the internal temperature is too high� High Altitude symbol ����������Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode� Downloaded From projector-manual.com NEC Manuals...

  • Page 63: List Of Menu Items

    AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC BACKGROUND BLUE BLUE, BLACK, LOGO FILTER MESSAGE 500[H] OFF, 100[H], 200[H], 500[H], 1000[H] The asterisk (*) indicates that the default setting varies depending on the signal. Downloaded From projector-manual.com NEC Manuals...
  • Page 64 VERSION DATA CONTROL ID (when [CONTROL ID] is set) CURRENT SIGNAL ALL DATA RESET NETWORK SETTINGS CLEAR LAMP HOURS CLEAR FILTER HOURS The asterisk (*) indicates that the default setting varies depending on the signal. Downloaded From projector-manual.com NEC Manuals...

  • Page 65: Menu Descriptions & Functions [Source]

    Selects what is connected to your S-VIDEO input-VCR or DVD player. NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or S- Video source. Downloaded From projector-manual.com NEC Manuals...

  • Page 66: Menu Descriptions & Functions [Adjust]

    PRESENTATION ����� Recommended for making a presentation using a PowerPoint file� VIDEO �������������������� Recommended for typical TV program viewing� MOVIE ������������������� Recommended for movies� GRAPHIC ��������������� Recommended for graphics� sRGB ��������������������� Standard color values [DETAIL SETTINGS] Downloaded From projector-manual.com NEC Manuals...
  • Page 67 Varies the color level from +/− green to +/− blue. The red level is used as reference. Input signal CONTRAST BRIGHTNESS SHARPNESS COLOR Computer (RGB DIGITAL) Computer (RGB ANALOG) Component Video, S-Video Yes = Adjustable, No = Not adjustable Downloaded From projector-manual.com NEC Manuals...
  • Page 68 The settings and adjustments for [CONTRAST], [BRIGHTNESS], [SHARPNESS], [COLOR], [HUE], and [REFER- ENCE] within [PRESET] will be returned to the factory settings. The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently select- ed will not be reset. Downloaded From projector-manual.com NEC Manuals...

  • Page 69: Image Options

    PHASE ������������������� Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk� (This is evident when part of your image appears to be shimmering�) Use [PHASE] only after the [CLOCK] is complete� Downloaded From projector-manual.com NEC Manuals...
  • Page 70 Select overscan percentage (0%, 5% and 10%) for signal. Projected image Overscaned by 10% NOTE: • The [0[%]] cannot be selected when VIDEO and S-VIDEO signals are used. • [OVERSCAN] is not available when [NATIVE] is selected for [ASPECT RATIO]. Downloaded From projector-manual.com NEC Manuals...
  • Page 71 NOTE: • When a non-computer signal is displayed, the [NATIVE] is not available. • When a signal with a higher resolution than the projector’s native resolution is displayed, [NA- TIVE] is not available. Downloaded From projector-manual.com NEC Manuals...
  • Page 72 When [16:9], [15:9], or [16:10] is selected in [ASPECT RATIO], the image is displayed with black borders on the top and bottom. You can adjust the vertical position from the top to the bottom of the black area. Downloaded From projector-manual.com NEC Manuals...
  • Page 73 BASS, TREBLE, BALANCE and 3D SURROUND. If this happens, return the adjustments of the projector to the factory preset ("0" for [BASS], "0" for [TREBLE], and "OFF" for [3D SURROUND]). Downloaded From projector-manual.com NEC Manuals...

  • Page 74: Menu Descriptions & Functions [Setup]

    OFF ������������������������ Does not save current keystone correction settings� It will return your keystone correction settings to “zero”� ON ������������������������� Saves current keystone correction settings Saving your change once affects all sources. The changes are saved when the projector is turned off. Downloaded From projector-manual.com NEC Manuals...
  • Page 75 Description Status of LAMP indicator This is the Default setting (100% Brightness). Select this mode to increase the lamp life (approx. 80% Brightness on NP3200 Steady Green light and approx. 88% Brightness on NP2200/ NP1200). NOTE: • The [LAMP LIFE REMAINING] and [LAMP HOURS USED] can be checked in [USAGE TIME]. Select [INFO.] → [USAGE TIME]. ( →...
  • Page 76 Turning ON/OFF Control ID [ID DISPLAY] ID DISPLAY ����������� This option turns on or off the ID number which is displayed when the ID SET button on the remote con- trol is pressed� ( → page 68) Downloaded From projector-manual.com NEC Manuals...
  • Page 77 “PLEASE CLEAN FILTER.” (→ page 77) Five options are available: OFF, 100[H], 200[H], 500[H], 1000[H] The default setting is 500[H]. NOTE: Your setting will not be affected even when [RESET] is done from the menu. Downloaded From projector-manual.com NEC Manuals...
  • Page 78 This feature turns on or off the SECURITY function. Unless the correct keyword is entered, the projector cannot project an image. (→ page 35) NOTE: Your setting will not be affected even when [RESET] is done from the menu. Downloaded From projector-manual.com NEC Manuals...
  • Page 79 No ID means that all the projectors can be operated together with a single remote control. To set “No ID”, enter “000” or press the CLEAR button. TIP: The range of IDs is from 1 to 254. Downloaded From projector-manual.com NEC Manuals...
  • Page 80 • The IDs can be cleared in a few days after the batteries are run down or removed. • Accidentally pressing any one of the buttons of the remote control will clear currently specified ID with batteries removed. Downloaded From projector-manual.com NEC Manuals...
  • Page 81 • Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical components such as the lamp. • Your setting will not be affected even when [RESET] is done from the menu. Downloaded From projector-manual.com NEC Manuals...
  • Page 82 Turns on or off the deinterlace function for a telecine signal. OFF ������������������������ Select this option if there is any jitter or artifacts in video� ON ������������������������� Default standard setting� NOTE: This feature is not available for RGB, 480p, 576p and HDTV signals. Downloaded From projector-manual.com NEC Manuals...
  • Page 83 Enabling Auto Power On [AUTO POWER ON(AC)] Turns the projector on automatically when the power cable is inserted into an active power outlet. This eliminates the need to always use the POWER button on the remote control or projector cabinet. Downloaded From projector-manual.com NEC Manuals...
  • Page 84 COMPUTER 2 �������� The signal from the COMPUTER 2 input will be output to the MONITOR OUT connector and AUDIO OUT jack� NOTE: When [COMPUTER 1] or [COMPUTER 2] is selected for [AUTO POWER ON(COMP1/2)], the [OUT TERMINAL] feature is not available. Downloaded From projector-manual.com NEC Manuals...

  • Page 85: Menu Descriptions & Functions [Info.]

    Replacement lamp 2000 3000 NP06LP • [TOTAL CARBON SAVINGS] This displays the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving cal- culation is based on the OECD (2008 Edition). Downloaded From projector-manual.com NEC Manuals...
  • Page 86 [SIGNAL TYPE] [VIDEO TYPE] [SYNC TYPE] [SYNC POLARITY] [SCAN TYPE] [WIRED LAN] [PROJECTOR NAME] [IP ADDRESS] [SUBNET MASK] [GATEWAY] [MAC ADDRESS] [VERSION] [PRODUCT] [SERIAL NUMBER] [FIRMWARE] Version [DATA] Version [CONTROL ID] (when [CONTROL ID] is set) Downloaded From projector-manual.com NEC Manuals...

  • Page 87: Menu Descriptions & Functions [Reset]

    Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press the ENTER button. NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu. Downloaded From projector-manual.com NEC Manuals...

  • Page 88: Maintenance

    Preparation: Replace the lamp before replacing the filters. NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement lamp. 1. Pull to remove the filter cover. Downloaded From projector-manual.com NEC Manuals...

  • Page 89: Cleaning The Cabinet And The Lens

    2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner. 3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens. Downloaded From projector-manual.com NEC Manuals...

  • Page 90: Replacing The Lamp

    Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement.
  • Page 91 3. Insert a new lamp housing until the lamp housing is plugged into the socket. CAUTION Do not use a lamp other than the NEC replacement lamp NP06LP. Order this from your NEC dealer. Secure it in place with the two screws.
  • Page 92 If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero. When the lamp time clock is reset to zero, the LAMP indicator goes out. Downloaded From projector-manual.com NEC Manuals...

  • Page 93: Using Optional Lenses

    7. Using Optional Lenses Five optional lenses are available for the NP3200/NP2200/NP1200. See the information described on this page to buy the appropriate lens for your screen size and throw distance. See page for installing the lens.  Table of Throw Distances and Screen Sizes for Optional Lenses [NP3200/NP2200/NP1200] NOTE: The values in the tables are design values and may vary.

  • Page 94: Lens Shift Adjustable Range

    NOTE: Lens shift is not available with the NP01FL optional lens. The NP01FL should be used only for “zero degree” applications. Desktop front projection Normal projection Position Vertical shift Max. 0.5V 0.5V 0.1H 0.1H Width of projected image Ceiling front projection Vertical shift Shift to left Shift to right Max. 0.5V Downloaded From projector-manual.com NEC Manuals...

  • Page 95: Replacing With Optional Lens

    If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt. • Please heed the following information if you own two or more NP3200/NP2200/NP1200 projectors and may in- terchange the standard lenses.
  • Page 96 Rotate the lens until you feel it click into place. Using the anti-theft screw to prevent theft of the lens Tighten the supplied anti-theft screw on the front bottom. Hole of anti-theft screw for lens unit Downloaded From projector-manual.com NEC Manuals...

  • Page 97: Appendix

    • Move the projector to a cooler location if the room where you are presenting is particularly too warm. • Clean the ventilation holes if they are clogged with dust. • Wait about 60 minutes until the inside of the projector becomes cool enough. Downloaded From projector-manual.com NEC Manuals...
  • Page 98 • Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 30) mode • Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→ page 58) For more information contact your dealer. Downloaded From projector-manual.com NEC Manuals...
  • Page 99 Usually, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.

  • Page 100: Specifications

    LCD Panel NP3200/NP2200/NP1200: 0.8" p-Si TFT active-matrix with Micro Lens Array (Aspect ratio 4:3) Resolution NP3200/NP2200/NP1200: 1024 × 768 pixels*¹ up to UXGA with scaling technology (up to SXGA+ @ 60 Hz on DVI-D) Standard Lens Manual zoom and focus: F1.7–2.2 f=24.4–32.5 mm...
  • Page 101 8. Appendix Power Consumption NP3200: 428W(100-130V AC)/412W(200-240V AC) in OFF for ECO MODE/345W(100-130V AC)/334W(200-240V AC) in ON for ECO MODE NP2200/NP1200: 396W(100-130V AC)/381W(200-240V AC) in OFF for ECO MODE/345W(100-130V AC)/334W(200-240V AC) in ON for ECO MODE NP3200/NP2200/NP1200: 12W(100-130V AC)/13W(200-240V AC) in NORMAL Mode for STANDBY MODE/0.4W(100-130V AC)/0.5W(200-...

  • Page 102: Cabinet Dimensions

    8. Appendix  Cabinet Dimensions 399/15.7" ス ゛ ーム Unit: mm/inch Downloaded From projector-manual.com NEC Manuals...

  • Page 103: Screen Size And Projection Distance

    The lower chart shows that the vertical distance between the projector foot and the screen top is approximately 1.5 m (59"). The projection angle can be adjusted up to 10°. (The lower chart shows that the projector is placed in a horizontal position) Downloaded From projector-manual.com NEC Manuals...
  • Page 104 15.65 - 20.83 616.2 - 820.2 0-381 0-150.0 H2 = Screen height (V) - H1 Screen center 88 mm/3.47" Lens center Projector foot Screen bottom NOTE: The values in the tables are design values and may vary. Downloaded From projector-manual.com NEC Manuals...

  • Page 105: Pin Assignments Of D-Sub Computer 1 Input Connector

    Green or Sync on Green Blue Ground Ground Red Ground Cr Ground Green Ground Y Ground Blue Ground Cb Ground No Connection Sync Signal Ground No Connection Bi-directional DATA (SDA) Horizontal Sync or Composite Sync Vertical Sync Data Clock Downloaded From projector-manual.com NEC Manuals...

  • Page 106: Compatible Input Signal List

    Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures. Downloaded From projector-manual.com NEC Manuals...

  • Page 107: Pc Control Codes And Cable Connection

    INPUT SELECT COMPUTER 3 INPUT SELECT VIDEO INPUT SELECT S-VIDEO PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF NOTE: Contact your local dealer for a full list of PC Control Codes if needed. Downloaded From projector-manual.com NEC Manuals...

  • Page 108: Cable Connection

    NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. Downloaded From projector-manual.com NEC Manuals...

  • Page 109: Troubleshooting Check List

    Projector is placed near a fluorescent light that can disturb the infrared remote controls� Still unchanged even though you press and hold the EXIT button for a minimum of 10 seconds� Batteries are new and are not reversed in installation� Downloaded From projector-manual.com NEC Manuals...
  • Page 110 Native resolution: Refresh rate: Video adapter: Other: Projector DVD player Video equipment Signal cable VCR, DVD player, Video camera, Video game or other NEC standard or other manufacturer’s cable? Model number: Length: inch/m Manufacturer: Distribution amplifier Model number: Model number: Switcher...

  • Page 111: Travelcare Guide

    This warranty allows customers to receive service on their product at 9) Other conditions stipulated in the warranty included with the the NEC and NEC-designated service stations in the countries listed product also apply. herein when temporarily traveling internationally for business or plea- sure.
  • Page 112 8. Appendix Visual Group Ltd. NEC Corporation of Malaysia Sdn. Bhd. Address: 28 Walls Road Penrose Auckland New Zealand Address: 33rd Floor, Menara TA One, 22, Jalan P. Ram- Telephone: 095250740 lee, 50250 Kuala Lumpur, Malaysia Fax Line: 095809607 Telephone:...
  • Page 113 8. Appendix P-1/ Date: TO: NEC or NEC’s Authorized Service Station: (Company & Name with signature) Dear Sir (s), I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your following conditions, and also the Service fee will be charged to my credit card account, if I don’t return the Loan units within the specified period.
  • Page 114 Application Sheet. list price to Credit Cards, which price will be informed by NEC Autho- rized Service Stations. Please see the attached listing of contacts for 1) Repair and Return: each country to arrange for pickup of the loan unit.
  • Page 115 © NEC Display Solutions, Ltd. 2009 7N951381 Downloaded From projector-manual.com NEC Manuals...

This manual is also suitable for:

Np2200Np1200

Table of Contents