Table of Contents
Advertisement
Quick Links
Manufacturer's Declaration of Conformity
This product has been manufactured in accordance with
the harmonized European standards, following the
provisions of the below stated directives:
93/42/EEC
2007/47/EC
Medical Device Directive
2014/31/EU
Non-automatic Weighing Instruments
Directive
Please see separate document showing on sticker of device for
above CE marking.
Authorized EU Representative:
Manufactured by:
Charder Electronic Co., Ltd.
No.103, Guozhong Rd., Dali Dist.,
Taichung City 412,Taiwan (R.O.C.)
FDA no.: D051882
IN-1012 [7025L] 04/2016
as
amended
35
by
Please keep the instruction manual at hand all the time for future reference.
MS 4600/4610
USER MANUAL
- 0 -
Advertisement
Table of Contents
Related Manuals for Charder MS 4600
Summary of Contents for Charder MS 4600
- Page 1 Non-automatic Weighing Instruments Directive Please see separate document showing on sticker of device for above CE marking. Authorized EU Representative: Manufactured by: Charder Electronic Co., Ltd. No.103, Guozhong Rd., Dali Dist., Taichung City 412,Taiwan (R.O.C.) MS 4600/4610 FDA no.: D051882 USER MANUAL IN-1012 [7025L] 04/2016 Please keep the instruction manual at hand all the time for future reference.
-
Page 2: Table Of Contents
NOTE TABLE OF CONTENTS PREFACE ....................2 GENERAL INFORMATION ..............2 SAFETY INSTRUCTION................. 2 ENVIRONMENTAL................. 3 CLEANING....................3 MAINTENANCE ..................3 WEIGHING OPERATION................ 4 WARRANTY-LIABILITY................ 4 DISPOSING OF THE SCALE ..............5 EXPLANATION OF THE GRAPHIC SYMBOLS........6 EMC guidance and manufacturer's declaration .......... 8 SPECIFICATION.................. -
Page 3: Preface
Observe the permissible ambient temperatures for use The device meets the requirements for electromagnetic compatibility. Do not exceed the maximum values specified in the applicable standards. If you have any problem, please contact your local CHARDER MEDICAL service partner. - 2 -... -
Page 4: Environmental
If any inaccuracies occur, please contact your local dealer or CHARDER MEDICAL service partner. 5. Installing the battery housing. 6. Reinstalling the battery cover. -
Page 5: Weighing Operation
CHARDER MEDICAL’s scope of responsibility, CHARDER shall have the right to either repair the fault or supply a replacement unit. Replaced parts shall be the property of CHARDER. Should the fault repairs or replacement delivery not be successful, the statutory provisions shall be valid. -
Page 6: Disposing Of The Scale
2. New Connection Description functioning shall be rendered null and void. If CHARDER Give new connection a name then click OK. provides and individual warranty, this means that the unit supplied will be free of faults for the length of the warranty 3. -
Page 7: Explanation Of The Graphic Symbols
PIN 5--GND Taichung City 412, Taiwan (R.O.C.) “Electro-medical appliance“ Connecting with PC- MS 4610 and MS 4600 both can be with attachment for type B connected to PC to transfer the weighing results. 1. Start Hyper Terminal Start Hyper Terminal program from clicking Start Menu →... - Page 8 RS232 interface cable (included in accessory kit), which is lower limit -20°C connected with the round plug at the back terminal. (MS 4600 cant (Transport and storage temperature print out the results directly through printer.) on packaging) After weighing and calculating BMI simply press PRINT key to print out the results.
-
Page 9: Emc Guidance And Manufacturer's Declaration
Harmonic emissions Class A those directly connected to the MS 4600: Switch ON the scale and long press [UNIT] key for 3 IEC 61000-3-2 public low-voltage power supply network that supplies seconds. Voltage fluctuations... - Page 10 2. MS 4600 Guidance and manufacturer’s declaration-electromagnetic immunity The MEDICAL SCALE MS4610 is intended for use in the electromagnetic environment specified below. Turn on the scale using key. The customer or the user of the MEDICAL SCALE MS4610 should assure that it is used in such an environment.
- Page 11 Power The MEDICAL SCALE USING BMI FEATURE 3 A/m 3 A/m frequency(50/60 MS4610 power Hz) magnetic frequency magnetic For BMI calculation, height is needed, therefore it is recommended field IEC fields should be at levels to measure the height of subject before starting weighing procedure 61000-4-8 characteristic of a typical location in a typical...
- Page 12 Radiated RF 3 V/m 80MHz to 2,5 3 V/m IEC 61000-4-3 The instrument will make flash Field strengths from fixed RF transmitters, as determined by an and beep sound and will display electromagnetic site survey the saved Pre-Tare Weight. should be less than the compliance level in each frequency range Interference may occur in the...
- Page 13 B. Enter Weight Using 0~9 Keys: DESCRIPTION EXAMPLE Recommended separation distance between portable and mobile RF communications equipment and the MEDICAL SCALE The MEDICAL SCALE MS4610 is intended for use in an electromagnetic Press PRE-TARE key, and the environment in which radiated RF disturbances are controlled. The customer or extreme left digit will blink.
-
Page 14: Specification
SPECIFICATION MS 4610- STORING AND RE-CALLING PRE-TARE WEIGHT MS4610 MS 4600 Model MS 4610 can store 5 sets of pre-tare values, and there are two (APPROVAL) (Non-Approval) methods to store pre-tare value – Using Dead Weight or Enter 300kg x... -
Page 15: Medical Scale Models Approval List
MEDICAL SCALE MODELS APPROVAL LIST USING TARE FUNCTION The Medical Scales MS4610 listed below are the certified models under the Council Directive for standard of 2007/47/EC Tare allows the user to zero the instrument to deduct the excess safety, health protection and accurate metrology characteristics weight of contained objects/person from the reading of the of medical scales: instrument, thus giving the true weight of the object/ person being... -
Page 16: Panel
But in case of highly unstable and weight is moving away from on the platform before the HOLD function stabilized, it is recommended to press HOLD key before the person moves on the tread platform. MS 4600 (non-approval version) - 15 - - 20 -... -
Page 17: Key Function
USING SCALE KEY FUNCTION MS 4610 WEIGHING Description Switch on the scale by press the key. The diagnostic scale ON/OFF Turn ON/OFF the scale 4keys / 20keys will start self-check and the software version will be displayed. PRINT Data transmission via PC (Weight , BMI , Height) The weighing value “0,00 kg”... -
Page 18: Lcd Display Symbols
MS 4600 LCD DISPLAY SYMBOLS Description PRE-TARE Indication 4 keys version Hold Indication NET WEIGHT Indication ON/OFF Turn ON/OFF the scale UNIT To select the weighing unit. (kg/lb) WEIGHT Indication BMI Indication To hold weighing result on the display / determine...
Need help?
Do you have a question about the MS 4600 and is the answer not in the manual?
Questions and answers