Table of Contents
Advertisement
Included Hardware
PACKAgEd In KIT
Fuselage
Left Wing with aileron & control horn
Right Wing with aileron & control horn
Vertical fin with rudder & control horn
Horizontal stab with elevator & control horn
Top hatch
Cowl with clear template
Canopy
Painted aluminum landing gear
Wheel pants (pair)
3/4 x 16-inch anodized wing tube
1/4 x 4-inch anodized wing tube
LAndIng gEAR BAg
Float mounting block
Wheel axle, 1
/
-inch
3
16
Wheel collar, 11/64-inch
3mm x 5mm machine screw for wheel collars
#4 self-tapping wood screw
4-40 x 3/8-inch socket head cap screws
8-32 x 3/4-inch machine screws for landing gear
#8 flat washers for landing gear
Nylon landing gear straps for float mount
Hangar 9 2
/
-inch wheels
3
4
#4 flat washers
ELEvAToR BAg
Nylon Clevis
Pushrod keeper
Silicone clevis retainer
#4 flat fender washers for bolt-on tail
Nylon insert lock nuts for bolt-on tail
RuddER BAg
Nylon clevis
Pushrod keeper
Silicone clevis retainer
Hangar 9 Saratoga Assembly Manual
MoToR MounT BAg
Cast aluminum motor mount
8-32 x 1-inch machine screws
8-32 x 3/4-inch machine screws
(1)
8-32 x 2
/
-inch machine screws
1
(1)
4
#8 flat washers
(1)
8-32 nylon insert lock nuts
(1)
1
/
-inch (48mm) EP standoffs
7
(1)
8
(1)
WIng BAg
(1)
4
/
-inch pushrod with L bend (aileron)
5
(1)
8
(1)
Nylon clevis
(2)
Pushrod keeper
(1)
Silicone clevis retainer
(1)
CoWL BAg
4-40 x 1/2-inch socket head cap screw for cowl
(1)
2
/
-inch spinner (yellow)
1
(2)
4
#4 washers for cowl
(4)
Silicone tubing
(4)
3mm x 10mm sheet metal screw
(8)
(2)
FuSELAgE BAg
(3)
23-inch pushrod with L bend (elevator)
(3)
23
/
-inch pushrod with L bend (rudder)
1
2
(4)
16
/
-inch throttle pushrod
1
2
(2)
Nylon clevis
(2)
Pushrod keeper
Silicone clevis retainer
Plywood throttle pushrod support
(1)
12-inch throttle pushrod housing
(1)
4-40 x 3/8-inch socket head screw
(1)
#4 washer
(2)
(2)
MISCELLAnEouS BAg
Velcro battery strap
1.5mm hex wrench
(1)
Foam radio holder
(1)
Pilot figure
(1)
using the Manual
(1)
This manual is divided into sections to help make assembly
(4)
easier to understand, and to provide breaks between each
(4)
major section. In addition, check boxes have been placed
(4)
next to each step to keep track of each step completed.
Steps with a single box () are performed once, while steps
(8)
with two boxes () indicate that the step will require
(4)
repeating, such as for a right or left wing panel, two servos,
(4)
etc. Remember to take your time and follow the directions.
ultraCote® Covering Colors
(2)
• Dark Yellow
(2)
• Black
(2)
• White
(2)
• 2-inch squares, Black/White HANU941
(2)
Before Starting Assembly
Before beginning the assembly of your model, remove
each part from its bag for inspection. Closely inspect the
(4)
fuselage, wing panels, rudder and stabilizer for damage. If
(1)
you find any damaged or missing parts, contact the place of
(4)
purchase.
(4)
If you find any wrinkles in the covering, use a heat gun or
(2)
covering iron to remove them. Use caution while working
around areas where the colors overlap to prevent separating
the colors.
(1)
(1)
HAN100 - Heat Gun
(1)
(1)
HAN150 - Covering Glove
(1)
(1)
(1)
HAN101 - Sealing Iron
(1)
(3)
HAN141 - Sealing Iron Sock
(3)
(2)
(1)
(3)
(1)
HANU889
HANU874
HANU870
3
Advertisement
Table of Contents
