Download Print this page
Hangar 9 Spitfire Mk.IX ARF Instruction Manual
Hangar 9 Spitfire Mk.IX ARF Instruction Manual

Hangar 9 Spitfire Mk.IX ARF Instruction Manual

Advertisement

Quick Links

Electric retract system
Thank you very much for purchasing our TRCM optional electric retract set,
all our products were passed strict QC before they shipped out to the customers.
In order to avoid probably trouble happen, we still would like you to follow the steps
below before you assemble our electric retracts to your plane.
1
. Connecting the circuit board to the battery and receiver.
2
Turn on the radio control to check the lights
.
on the circuit board, if the lights turn on green
or turn on red orderly,0.5 second after each
from the right to the left and all the lights will
turn off after 15 seconds, then the circuit will
work normally. Otherwise the circuit will be a
defective one if you make sure the setting on
your radio control are correct, please don't use
it but contact with your supplier in time.
In order to let the customers have
more choices, we don't provide a
uniform plugs.
For retracts
7.4V 30C
4
Assemble the electric retracts to the plane
.
after several times smoothly running.
Please don't ceaselessly turn and off the switch in 2 seconds,
if you do this way, the circuit board will be heated.
3
Link the electric retract units to the
.
circuit boards after the above two
steps, check again the electric retracts
to see if they can work normally or not.
Receiver
1
4.8V
For receiver
Spitfire Mk.IX ARF
Speci cation:
Wing Span:
2058mm/81in
Length:
1715mm/67.5in
Flying Weight: ~7.6kg
Wing area:
74.95 dm2
Engine:
35cc-40cc
R/C System:
2.4Ghz 6ch
Servo: GP *7 ; EP * 6
Battery: LI-PO 5S*2 5000mAh 30C
ESC: 120A High voltage Brushless ESC

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

This R/C airplane is not a toy!
(The people under 18 years old is forbidden from flying this model)
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.

Advertisement

loading

Summary of Contents for Hangar 9 Spitfire Mk.IX ARF

  • Page 1: Instruction Manual

    QC before they shipped out to the customers. In order to avoid probably trouble happen, we still would like you to follow the steps Spitfire Mk.IX ARF below before you assemble our electric retracts to your plane.
  • Page 2 Accessories packing list Gasoline tube Gear door TP Screw (2.3x8mm) TP Screw (2.3x12mm) Servo tray(2mm) TP Screw (3x20mm ) Gasoline Screw (2.6x12mm) Canopy Fiberglass Screw (2x10mm) Canopy PVC Screw (3x10mm) 6 channel radio for aiplane is highly recommended for this model. Screw (3x20mm) Fiber deconations scoop...
  • Page 3 Epoxy the ber deconations to aprropriate position Assemble the canopy to the cockpit with screws. Assemble the aileron to main wing with instant type AB glue. Be careful Accessory list for the coming installation steps. on the bottom of the wing. to ensure the moving parts of the hinges are able to move freely.
  • Page 4 Accessory list for the coming installation steps. Epoxy the pin hinges to the slots in the ap. Canopy (Fiberglass) Canopy (PVC) Fiber deconations scoop Antenna Scale gun set TP Screw (2.3x8mm) Screw (3x20mm) Pin hinge(24x24mm) Assembly of the fuel tank(please notice that the plug of Assemble the servo tray to the wing with screws Keep some space about 1mm width between Assemble the antenna to the fuselage with screw.
  • Page 5 Assemble the servo tray to the wing with screws and Install the servo as the illustration below. epoxy the ber horn to the ap. TP Screw (2.3x12mm) 1.5mm Masking tape TP Screw (2.3x12mm) Install the engine to the engine mount with screws. Accessory list for the coming installation steps.
  • Page 6 The sketch map of the steel wires working in Assemble the retracts to the appropriate position Assemble the tail gear cover with screws as below. The sketch map of the wing ts well to the fuselage. the fuselage. in the gear house. TP Screw (3x20mm) Rudder servo TP Screw (2.3x8mm)
  • Page 7 The sketch map when assemble the tail landing Assemble the steel wires well to the rudder horn Epoxy the elevator to the stabilizer. Accessory list for the coming installation steps. gear to the wheel steeling mount. and tail wheel. Steel wire (0.5x3000mm) Horn pivot &...
  • Page 8 Assemble the stab to the fuselage drill a hole to Assemble the push rod branches to the horns on Epoxy the pivot & round hinges to the rudder. Accessory list for the coming installation steps. the other section stab. the elevator. Screw (2x10mm) Steel wire (0.5x3000mm) Locknut (2mm )