Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Manual
Advertisement
Table of Contents
Related Manuals for Monogram ZIP360NH
Summary of Contents for Monogram ZIP360NH
- Page 1 Design Guide with Installation Instructions 36” Built-In French Door, Bottom-Freezer Refrigerators 31-49082-1 224D3560P003 04-15 GE monogram.com...
-
Page 2: Safety
Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area. For Monogram local service in your area, call 1.800.444.1845. For Monogram Parts and Accessories, call 1.800.626.2002. - Page 3 Consignes de Sécurité Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », «...
-
Page 4: Table Of Contents
Contents Safety 2, 3 Installation Instructions Tools, Hardware, Materials, Flooring Instructions for Standard Installation 5-21 Grounding the Refrigerator Design Guide Step 1. Remove Packaging The Installation Space Step 2. Install Water Line Dimensions and Clearances Step 2A. Water Line with Reverse Osmosis System Custom Handle Design Guide Step 3. -
Page 5: Instructions For Standard Installation
Instructions for Standard Installation... -
Page 6: Design Guide
Design Guide - Standard Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35-1/2" 35" Finished Width The finished 25-3/8" Case Width Case Depth cutout width Wall View 2-5/16" * Shipping height. The must be refrigerator can be adjusted to fit into a 35-1/2”. -
Page 7: Custom Handle Design Guide
Side panels must be used whenever the sides of the • Install it on a floor strong enough to support it fully refrigerator will be exposed. loaded. Optional Accessory Kits • ZKHFD2H: Monogram Tubular Stainless Steel handles designed to fit 3/4” overlay panels. -
Page 8: 3/4" Overlay Panel Dimensions
Design Guide - Standard Installation 3/4” OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a thick backer panel which slides into the trim. A spacer ”... -
Page 9: 1/4" Framed Panel Dimensions
Design Guide - Standard Installation 1/4” FRAMED PANEL DIMENSIONS 5/16" Trim If you choose to install framed panels, they must be cut Door Reveal to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. 1/4"... -
Page 10: 130° Door Swing
Design Guide - Standard Installation Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets Refrigerator may require filler strips to prevent 23-7/8" From interference with cabinet door swing. Rear of The opening must allow for filler strips. Refrigerator 1"... -
Page 11: Door Swing
Design Guide - Standard Installation Frameless Cabinets: The case trim overlaps cabinets at the top and Refrigerator sides. Therefore, frameless cabinets may require Case Trim filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8"... -
Page 12: Installation Instructions
Installation Instructions TOOLS REQUIRED HARDWARE SUPPLIED • Tinsnips to cut banding • Water filter bypass plug • Stepladder • Anti-Tip brackets • Bucket • 1/4” nut and ferrule • Level • Custom Handle Trim Kit (Shorter box taped to the front of •... -
Page 13: Step 1 Remove Packaging
Installation Instructions STEP 1 REMOVE PACKAGING • The unit is secured to the skid with 2 full-length tie-down straps. Remove WARNING Tip Over Hazard. the ten 5/16” bolts from the Refrigerator is much heavier at the top than at the base channels in the tie- bottom. -
Page 14: Step 2A. Water Line With Reverse Osmosis System
Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM • The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts. The wall bracket will be attached to Skip this step when not using an RO System the wall in 4 places. - Page 15 Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 4 ANIT-TIP PROCEDURE (CONT) • The anti-tip wall bracket has a series of holes. Select 2 • Place your thumb between the plastic straps and bend holes that match with the located studs. Make sure the up and down to snap the straps off at the wall.
-
Page 16: Step 5 Level Refrigerator
Installation Instructions STEP 6 SECURE UNIT TO WALL STEP 5 LEVEL REFRIGERATOR • The “L” rod can be found in the upper left corner of All models have 4-point leveling. The front is supported the unit in the access compartment. Look through the by leveling legs, the rear is supported by adjustable access compartment to make sure the rod lines up wheels. -
Page 17: Step 7 Alternate Anti-Tip Procedure
Installation Instructions STEP 8 ADJUST DOOR SWING STEP 7 ALTERNATE ANTI-TIP PROCEDURE NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open The refrigerator must be secured to prevent tipping. fully to 115°, you may change the door swing to a 90° If the anti-tip bracket cannot be used, this alternate opening. -
Page 18: Step 9 Install Grille Panel
Installation Instructions - Standard Installation STEP 9 INSTALL GRILLE PANEL • Raise the access panel to the stop position. • Loosen the screws on the side trim behind the frame. • Reassemble the bottom trim. Tighten the screws. Remove the bottom trim. •... -
Page 19: Step 10A Install Overlay Panels
Installation Instructions - Standard Installation STEP 10A INSTALL OVERLAY PANELS IF YOU ARE INSTALLING FRAMED PANELS, GO TO STEP 10. Supplied handle shown Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips head screws from •... -
Page 20: Step 11 Connect Water Supply
Installation Instructions STEP 11 CONNECT WATER SUPPLY STEP 12 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. Raise Grille Panel Electrical Outlet • Check to make sure power to refrigerator is on by House Refrigerator Water Supply... -
Page 21: Step 14 Install Toekick
Installation Instructions STEP 14 INSTALL TOEKICK INSPECT FINAL INSTALLATION • Locate the supplied toekicks (shipped taped to the Check door alignment side of the refrigerator. Stand back away from the refrigerator to inspect the • The narrower set of toe kicks will be used with final installation. -
Page 22: Instructions For Flush Installation
Instructions for Flush Installation... -
Page 23: Design Guide
Design Guide - Flush Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 39" 35" 25-3/8" Finished Width Case Width Case Depth Wall View 4-1/16" * Shipping height. The refrigerator can be 6" adjusted to fit into a *84" From ” cutout that is 85 max. -
Page 24: 1/2" Overlay Panel Dimensions
Design Guide - Flush Installation 1/2” OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be Door 1/2" secured to a 1/4” thick backer panel which slides into the Overlay trim. -
Page 25: 3/4" Decorative Panel Dimensions
Design Guide - Flush Installation 3/4” DECORATIVE PANEL DIMENSIONS CUSTOMIZATION BASICS: For a more custom appearance, overlay panels may be Framed Or Overlay Panels, Custom installed to give a flush appearance with surrounding cabinets. The overlay panel must be 3/4” thick. Panel Handles and Accessory Kits attaches to included brackets to provide mounting to the These refrigerators are designed to be customized with... -
Page 26: 3/4" Raised Fresh Food Door Panel Routing
Design Guide - Flush Installation 3/4” RAISED FRESH FOOD DOOR PANEL ROUTING For 3/4” raised door panels, routing is required. The router depth is 1/4” all the way around the panel back. Additional panel width reductions are required per the diagrams below. This will create a “picture frame” routing that will slide onto the attached door trim. -
Page 27: 3/4" Raised Freezer Drawer Panel Routing
Design Guide - Flush Installation 3/4” RAISED FREEZER DRAWER PANEL ROUTING For 3/4” raised door panel, routing is required. The router depth is 1/4” all the way around the panel back. Additional panel width reductions are required per the diagrams below. This will create a “picture frame” routing that will slide onto the attached door trim. -
Page 28: 3/4" Raised Grille Panel Routing
3/4” PANEL SIDE VIEW ROUTER DEPTH 1/4” ROUTER DEPTH 1/4” (AFTER ROUTING) 2-1/16” 2-1/16” Front LEFT RIGHT SIDE SIDE Back 3/4” PANEL BOTTOM VIEW (AFTER ROUTING) Optional Accessory Kit • ZKHFD2H: Monogram Tubular Stainless Steel handles designed to fit 3/4” overlay panels. -
Page 29: Side Panels
Design Guide - Flush Installation SIDE PANELS SIDE CLEATS Side panels must be used Wood cleats are required to be installed vertically 24" whenever the sides of down both sides of the cabinet opening to provide the refrigerator will be depth stop for the refrigerator when installed into the opening. -
Page 30: Installation Instructions
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 35” long 2x4 for Anti-Tip support • Stepladder • 1/4” copper water line tubing or GE SmartConnect ™ • Bucket Refrigerator Tubing kits • Level • Water shut-off valve •... -
Page 31: Step 1 Remove Packaging
Installation Instructions STEP 1 REMOVE PACKAGING • The unit is secured to the skid with 2 full-length tie-down straps. Remove WARNING Tip Over Hazard. the ten 5/16” bolts from the Refrigerator is much heavier at the top than at the base channels in the tie- bottom. -
Page 32: Step 2A. Water Line With Reverse Osmosis System
Installation Instructions STEP 5 ANIT-TIP PROCEDURE STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING Tip Over Hazard. Skip this step when not using an RO System These refrigerators are top heavy, especially If the water supply to the refrigerator is from a Reverse with any doors open, and must be secured to Osmosis Water System, use the refrigerator’s filter bypass prevent tipping forward which could result in... - Page 33 Installation Instructions - Flush Installation STEP 5 INSTALL ANTI-TIP BRACKET (cont.) • Gently pull back at the ends of the plastic straps to • Locate at least 2 studs on the back wall. Mark these make the channel rest flush behind the wall. points on the horizontal line.
-
Page 34: Step 6 Level Refrigerator
Installation Instructions - Flush Installation STEP 5 ANIT-TIP PROCEDURE (CONT) CONNECT POWER CORD: IMPORTANT: When the refrigerator is installed under a soffit or if there is not enough height for this method • Before pushing the refrigerator into the opening, plug of security, brackets cannot be used. -
Page 35: Step 8 Alternate Anti-Tip Procedure
Installation Instructions - Flush Installation STEP 9 ADJUST DOOR SWING STEP 8 ALTERNATE ANTI-TIP PROCEDURE NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open The refrigerator must be secured to prevent tipping. fully to 115°, you may change the door swing to a 90°... -
Page 36: Step 10 Install Grille Panel
Installation Instructions - Flush Installation STEP 10 INSTALL GRILLE PANEL • Raise the access panel to the stop position. • Loosen the screws on the side trim behind the frame. • Reassemble the bottom trim. Tighten the screws. Remove the bottom trim. •... -
Page 37: Step 12 Connect Water Supply
Installation Instructions STEP 12 CONNECT WATER SUPPLY STEP 13 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. Raise Grille Panel Electrical Outlet • Check to make sure power to refrigerator is on by House Refrigerator Water Supply... -
Page 38: Step 15 Install Toekick
Installation Instructions STEP 15 INSTALL TOEKICK INSPECT FINAL INSTALLATION • Locate the supplied toekicks (shipped taped to the side Check door alignment of the refrigerator. Stand back away from the refrigerator to inspect the • The wider set of toe kicks will be used for flush final installation. -
Page 39: Instructions For Stainless Steel Installation
Instructions for Stainless Steel Installation... -
Page 40: Design Guide
Design Guide - Stainless Steel Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35-1/2" 35" Finished Width The finished 25-3/4" Stainless Steel Models Case Width Case Depth Wall View cutout width 2-5/16" * Shipping height. The must be refrigerator can be adjusted to fit into a 35-1/2”. -
Page 41: Customization Basics
• Install it on a floor strong enough to support it fully Stainless steel wrapped refrigerators with beveled edges loaded. and tubular stainless steel handles that coordinate with other Monogram appliances. These models are shipped ready for installation. Side Panels Side panels must be used whenever the sides of the refrigerator will be exposed. -
Page 42: 130° Door Swing
Design Guide - Stainless Steel Installation Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets Refrigerator may require filler strips to prevent 23-7/8" From interference with cabinet door swing. Rear of The opening must allow for filler strips. Refrigerator 1"... -
Page 43: 90° Door Swing
Design Guide - Stainless Steel Installation Frameless Cabinets: The case trim overlaps cabinets at the top and Refrigerator sides. Therefore, frameless cabinets may require Case Trim filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8"... -
Page 44: Installation Instructions
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 35” long 2x4 for Anti-Tip support • Stepladder • 1/4” copper water line tubing or GE SmartConnect ™ • Bucket Refrigerator Tubing kits • Level • Water shut-off valve •... -
Page 45: Step 1 Remove Packaging
Installation Instructions STEP 1 REMOVE PACKAGING • The unit is secured to the skid with 2 full-length tie-down straps. Remove WARNING Tip Over Hazard. the ten 5/16” bolts from the Refrigerator is much heavier at the top than at the base channels in the tie- bottom. -
Page 46: Step 2A. Water Line With Reverse Osmosis System
Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM • The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts. The wall bracket will be attached to Skip this step when not using an RO System the wall in 4 places. - Page 47 Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 4 ANIT-TIP PROCEDURE (CONT) • The anti-tip wall bracket has a series of holes. Select 2 • Place your thumb between the plastic straps and bend holes that match with the located studs. Make sure the up and down to snap the straps off at the wall.
-
Page 48: Step 5 Level Refrigerator
Installation Instructions STEP 6 SECURE UNIT TO WALL STEP 5 LEVEL REFRIGERATOR • The “L” rod can be found in the upper left corner of All models have 4-point leveling. The front is supported the unit in the access compartment. Look through the by leveling legs, the rear is supported by adjustable access compartment to make sure the rod lines up wheels. -
Page 49: Step 7 Alternate Anti-Tip Procedure
Installation Instructions STEP 8 ADJUST DOOR SWING STEP 7 ALTERNATE ANTI-TIP PROCEDURE NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open The refrigerator must be secured to prevent tipping. fully to 130°, you may change the door swing to a If the anti-tip bracket cannot be used, this alternate 115°... -
Page 50: Step 9 Connect Water Supply
Installation Instructions STEP 9 CONNECT WATER SUPPLY STEP 10 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. Raise Grille Panel Electrical Outlet • Check to make sure power to refrigerator is on by House Refrigerator Water Supply... -
Page 51: Step 12 Install Toekick
Installation Instructions STEP 12 INSTALL TOEKICK INSPECT FINAL INSTALLATION • Locate the supplied toekick (shipped taped to Check door alignment the side of the refrigerator). Install the toekick Stand back away from the refrigerator to inspect the assembly with the 2 screws provided, adjust to the final installation. - Page 52 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
Need help?
Do you have a question about the ZIP360NH and is the answer not in the manual?
Questions and answers