Additional Warnings; Technical Data - Bostitch MB2140-E Original Instructions Manual

POWER ADJUSTMENT (TU-216-2330-E / TU-216-1825-E)
© Stanley Bostitch
For maximum power: rotate valve anticlockwise as far as possible. (Fig. 6)
To reduce power: rotate valve clockwise for up to 30% reduction. (Fig. 7)
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
TOOL OPERATION CHECK (TU-216-2330-E / TU-216-1825-E):
WARNING! Remove all fasteners from tool before performing tool operation check.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
A. With finger off the trigger, hold the tool with a firm grip on the handle.
B. Place the nose of the tool against the work surface.
C. Raise the secondary trigger device.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
D. Pull the trigger to cycle the tool. Release the trigger and cycle is complete.
die CE-Richtlinien für Produkte.
WARNING! With the secondary trigger device raised, the tool will cycle each time the trigger is pulled!
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.

ADDITIONAL WARNINGS:

WARNING (TU-216-2330-E / TU-216-1825-E)! The secondary trigger device should be checked periodically, to
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
ensure it is operating correctly.
produkterne.
While following the above tool operation check notes, release the secondary safety trigger and the operating trigger
simultaneously, this should automatically lockout the operating trigger, preventing the tool from being actuated.
The tool should only then operate again when the secondary trigger device is raised and the operating trigger is
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
depressed.
yhdenmukaisuutta.
WARNING! If the tool fails to work correctly contact you local STANLEY service centre or distributor for advice
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
before continuing to use it.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
WARNING (TU-216-2330-E / TU-216-1825-E)! Under no circumstances should the secondary trigger device or the
operating trigger be by-passed, modified or removed.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
FASTENER JAM CLEARING:
WARNING! Always disconnect air supply before clearing a jammed fastener.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
TO CLEAR A JAMMED FASTENER:
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
1. Release the magazine and pull it back to stop pin feeding.
2. Loosen the two screws as shown in (Fig. 8) by one full turn.
conformidade com a CE para os produtos.
3. Slide cover down until the two large clearance holes line up with the two screw heads as shown in (Fig. 9).
4. Pull the cover away from nose as shown in (Fig. 10).
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
5. Remove the jammed fastener.
conformidad con las normas CE de los productos.
6. Re-install cover, slide it up, tighten the two screws and close magazine.
7. Reconnect air hose.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
UTILITY HOOK (MB2140-E- Fig 11)
conformidad con las normas CE de los productos.
These tools include an additional utility hook suitable for storage and temporary hanging of the tool.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
WARNING! Never use the utility hook to hang the tool from the body, clothing or belt.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie

TECHNICAL DATA:

stanowią deklaracji zgodności CE prezentowanych produktów.
Please look for the technical data in the table marked ? at the end of this manual.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
A Length mm.
výrobky. B Height mm.
C Width mm.
D Weight Kg.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
E Noise L , 1s, d
PA
a termék CE-megfelelőségét.
F Noise L , 1s, d
WA
G Noise L , 1s, 1m
PA
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
H Vibration m/s
conformitatea CE pentru produse.
I P max Bar
J P min Bar
2
K Air consumption per shot @ 5.6 Bar
L Activation type
M Summer lubricant
N Winter lubricant
O O-ring lubricant
P Fastener Name
Q Dimensions mm.
R Head/crown
S Magazine capacity
T New Driver Length mm.
U Max. Depth Inside Piston mm.