Bostitch N80CB Operation And Maintenance Manual
  1. Manuals
  2. Brands
  3. Bostitch Manuals
  4. Nail Gun
  5. N80CB
  6. Operation and maintenance manual

Bostitch N80CB Operation And Maintenance Manual

Coil-fed pneumatic nailers
Hide thumbs Also See for N80CB:
Table of Contents

Advertisement

Quick Links

See also: Operation & Maintenance Manual , Technical Data Manual
N80CB
COIL-FED PNEUMATIC NAILERS
CLAVADORAS NEUMÁTICAS ALIMENTADAS POR ROLLO
CLOUEURS PNEUMATIQUES À ENROULEMENT
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN y DE MANTENIMIENTO
MANUEL D'INSTRUCTIONS et D'ENTRETIEN
ADVERTENCIA:
ATTENTION:
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL,
TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU
HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DIS-
TRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN
ESTUDIAR ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVER-
TENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS
INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA. SI TIENE
ALGUNA DUDA, COMUNÍQUESE CON SU REPRESENTANTE DE BOSTITCH O CON SU
DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D'UTILISER L'APPAREIL.
PRÊTER UNE ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ
ET AUX AVERTISSEMENTS. GARDER CE MANUEL AVEC L'OUTIL POUR FUTURE
RÉFÉRENCE.
SI
VOUS
AVEZ
DES
QUESTIONS,
CONTACTEZ
VOTRE
REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH.
102775 REV F 2/00
Stanley Fastening Systems

Advertisement

Table of Contents
loading

Related Manuals for Bostitch N80CB

Summary of Contents for Bostitch N80CB

  • Page 1 ESTUDIAR ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVER- TENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA. SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR. LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL.

  • Page 2: Table Of Contents

    To obtain warranty service, return the product at your expense together with proof of pur- chase to a Bostitch Regional or authorized warranty repair center. You may call us at 1- 800-556-6696 for the location of authorized warranty service centers in your area.

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool.

  • Page 4: Tool Specifications: Air Consumption & Operating Pressure

    DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE. AIR CONSUMPTION: The N80CB requires 7.2 cubic feet per minute of free air to operate at the rate of 100 nails per minute, at 80 p.s.i.g. (5.6 kg/cm ). Take the actual rate at which the tool will be run to determine the amount of air required.

  • Page 5: Air Supply: Fittings, Hoses, Filters, Regulators

    Frequent, but not excessive, lubrication is required for best performance. Oil added through the air line connection will lubricate the internal parts. Use BOSTITCH Air Tool Lubricant, Mobil Velocite #10, or equivalent. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance.

  • Page 6: Loading The Tool

    Note: The canister is adjusted correctly for 1-1/2” and 1-3/4” nails when “1-3/4 (45)” appears in the window of the canister bottom. NOTE: Use only nails recommended by Bostitch for use in Bostitch N80CB Series nailers or nails which meet Bostitch specifications.

  • Page 7: Operating The Tool

    THIS MANUAL. II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL. There are three available systems on BOSTITCH pneumatic tools. They are: 1. TRIGGER OPERATION 2. CONTACT TRIP OPERATION 3. SEQUENTIAL TRIP OPERATION OPERATION 1.

  • Page 8: Tool Operation Check

    IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANU- AL OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.

  • Page 9: Basic Tool Function Diagram

    BASIC TOOL OPERATION Bostitch pneumatic tools are cycled by a compressed air operated single piston design. The following illustrations show the four functional cycles that occur when the tool is operated to drive a fastener: FIG.1 FIG.2 EXHAUST OPEN AT REST...

  • Page 10: Trouble Shooting

    COIL NAILERS Skipping fasteners; intermittent feed Feed piston dry ....Add BOSTITCH Air Tool Lubricant in hole in feed piston cover Feed piston O-rings cracked/worn ..Replace O-rings/check bumper and spring.

  • Page 11: Driver Maintenance/Adjusting Exhaust

    Loosen screw as shown. Adjust to desired exhaust direction and tighten screw. ACCESSORIES AVAILABLE: BC601 4 oz. Bostitch Air-Tool Lubricant BC602 1 pint Bostitch Air-Tool Lubricant BC603 1 pint Bostitch “Winter-Formula” Air-Tool Lubricant BC604 1 quart Bostitch Air-Tool Lubricant 100679 Lube 1 lb. can SEQ1 Sequential Trip Conversion Kit...

Table of Contents