Sony DCR-TRV140 Service Manual page 37

Dubbing only desired scenes
– Digital program editing
(3) Setting your camcorder and the
VCR to face each other
Locate the infrared rays emitter of your
camcorder and face it towards the remote
sensor of the VCR.
Set the devices about 30 cm (12 in.) apart, and
remove any obstacles between the devices.
Infrared rays emitter/
A/V connecting cable (supplied)/
Dubbing only desired scenes
– Digital program editing
Step 2: Setting the VCR to operate
with the i.LINK cable
(DV connecting cable)
When you connect using the i.LINK cable (DV
connecting cable) (optional), follow the
procedure below.
(1) Set the POWER switch to PLAYER on your
camcorder.
(2) Turn the power of the connected VCR on,
then set the input selector to DV input.
When you connect a digital video camera
recorder, set its POWER switch to VCR/VTR.
(3) Press MENU to display the menu.
(4) Turn the SEL/PUSH EXEC dial to select ,
then press the dial.
(5) Turn the SEL/PUSH EXEC dial to select
VIDEO EDIT, then press the dial.
(6) Turn the SEL/PUSH EXEC dial to select EDIT
SET, then press the dial.
(7) Turn the SEL/PUSH EXEC dial to select
CONTROL, then press the dial.
(8) Turn the SEL/PUSH EXEC dial to select
i.LINK, then press the dial.
1
3
MENU
4 6-8
O T H E R S
B E E P ME L OD Y
COMMA ND E R
D I S P L A Y
V I D EO E D I T
R E T URN
V I D EO E D I T
MA R K
UNDO
E R A S E A L L
[ ME NU ] : E ND
S T A R T
E D I T S E T
T O T A L
S C E N E
[ ME NU ] : E ND
5
V I D EO E D I T 0 : 0 0 : 0 0 : 0 0
V I D E O E D I T
MA R K 1 I N
UNDO E D I T S E T
E R A S E A L L
S T A R T
E D I T S E T
T O T A L 0 : 0 0 : 0 0 : 0 0
S C E N E 0
[ ME NU ] : E ND
[ ME N U ] : E N D
–
(3)
Remote sensor/
–
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
V I D E O E D I T 0 : 0 0 : 0 0 : 0 0
0 : 0 0 : 0 0 : 0 0
E D I T S E T
CONTROL I R
A D J T E S T i L I N K .
"C U T - I N "
I R "C U T - O U T "
I R S E T U P
P A U S E M O D E
0 : 0 0 : 0 0 : 0 0
0 I R T E S T
R E T U R N
[ ME N U ] : E N D
0 : 0 0 : 0 0 : 0 0 V I D E O E D I T 0 : 0 0 : 0 0 : 0 0
E D I T S E T
I R i . L I N K
CONTROL CONTROL
A D J T E S T i L I N K . A D J T E S T
"C U T - I N " "C U T - I N "
"C U T - O U T " "C U T - O U T "
I R S E T U P I R S E T U P
P A U S E M O D E P A U S E M O D E
I R T E S T I R T E S T
R E T U R N R E T U R N
[ ME N U ] : E N D
DCR-TRV140/TRV140E/TRV140M
Dubbing only desired scenes
– Digital program editing
(4) Confirming the VCR operation
1 Insert a recordable tape into the VCR,
then set to recording pause.
2 Turn the SEL/PUSH EXEC dial to select
IR TEST, then press the dial.
3 Turn the SEL/PUSH EXEC dial to select
EXECUTE, then press the dial.
If the VCR starts recording, the setting is
correct.
When finished, the indicator changes to
COMPLETE.
When the VCR does not operate correctly
•After checking the code in "About the IR
SETUP code", set the IR SETUP or the
PAUSEMODE again.
•Place your camcorder at least 30 cm (12 in.)
away from the VCR.
•Refer to the operating instructions of your VCR.
115 116
Dubbing only desired scenes
– Digital program editing
Step 3: Adjusting the
synchronisation of the VCR
You can adjust the synchronisation of your
camcorder and the VCR. Have a pen and paper
ready for notes. Before operation, eject the
cassette from your camcorder.
(1) Set the POWER switch to PLAYER on your
camcorder.
(2) Insert a blank tape (or a tape you want to
record over) into the VCR, then set to
recording pause.
When you select i.LINK in CONTROL, you
do not need to set to recording pause.
(3) Press MENU to display the menu.
(4) Turn the SEL/PUSH EXEC dial to select
, then press the dial.
(5) Turn the SEL/PUSH EXEC dial to select
VIDEO EDIT, then press the dial.
(6) Turn the SEL/PUSH EXEC dial to select
EDIT SET, then press the dial.
(7) Turn the SEL/PUSH EXEC dial to select
ADJ TEST, then press the dial.
(8) Turn the SEL/PUSH EXEC dial to select
EXECUTE, then press the dial.
IN and OUT are recorded on an image for 5
times each to calculate the numerical values
for adjusting the synchronisation.
The EXECUTING indicator flashes on the
screen. When finished, the indicator
changes to COMPLETE.
(9) Rewind the tape in the VCR, then start slow
playback.
Take a note of the opening numerical value
for each IN and the closing numerical value
for each OUT.
(10) Calculate the average of all the opening
numerical values for each IN, and the
average of all the closing numerical values
for each OUT.
(11) Turn the SEL/PUSH EXEC dial to select
"CUT-IN", then press the dial.
(12) Turn the SEL/PUSH EXEC dial to select the
average numerical value of IN, then press
the dial.
The calculated start position for recording is
set.
(13) Turn the SEL/PUSH EXEC dial to select
"CUT-OUT", then press the dial.
(14) Turn the SEL/PUSH EXEC dial to select the
average numerical value of OUT, then press
the dial.
The calculated stop position for recording is
set.
117 118
1-27
–
(4)
1
2
3
2 3
V I D E O E D I T 0 : 0 0 : 0 0 : 0 0 V I D E O E D I T
E D I T S E T E D I T S E T
CONTROL CONTROL
A D J T E S T A D J T E S T
"C U T - I N " "C U T - I N "
"C U T - O U T " ENGAGE "C U T - O U T "
I R S E T U P REC PAUSE I R S E T U P
P A U S E M O D E P A U S E M O D E
I R T E S T I R T E S T
RETURN C O M P L E T E
R E T U R N EXECUTE R E T U R N
[ ME N U ] : E N D [ ME N U ] : E N D
•
•
•
–
0 : 0 0 : 0 0 : 0 0