Advertisement
Figure 4.
OnSite web management home page
Now you can use the OnSite's web management pages to complete your configuration (see section
3.
"Complete the installation"
5.0 Connect the WAN port
The OnSite 2603/T, 2603/K, and 2620 come with a T1/E1 WAN interface (presented on an RJ-48C connector
with selectable line impedances of 100-ohms for T1 and 120-ohms for E1 lines). The Model 2603 has one RJ-
48C connector and the 2620 has two. The Model 2603/K and 2620/KK also come with dual BNC connectors for
alternate connection to unbalanced 75-ohm E1 lines.
To connect the WAN port on a Model 2620 or Model 2603/T, or if you plan to use the RJ-48C port on a 2603/K,
refer to section "Connecting to the RJ-48C WAN port". Otherwise, refer to section "Connecting to the unbalanced
75-ohm TX and RX WAN ports (Model 2603/K and 2620/KK only)" to install cables onto the BNC connectors on
the 2603/K and 2620/KK models.
Connecting to the RJ-48C WAN port
Obtain a twisted-pair cable with an RJ-48C plug connector at each end.
1.
Plug one end of the cable into the RJ-48C socket (labeled
2.
Plug the other end of the cable into the T1/E1 device.
3.
Repeat steps 1 through 3 to install the remaining WAN cables on a Model 2620
4.
Connecting to the unbalanced 75-ohm TX and RX WAN ports (Model 2603/K and 2620/KK only)
Obtain a coaxial cable with a BNC connector at each end.
1.
Plug one end of the cable into the transmit socket (labeled
2.
of the cable into the receive port of the E1 device.
Plug one end of the cable into the receive socket (labeled
3.
the cable into the transmit port of the E1 device.
6
on page 7).
WAN
) on the OnSite Router.
TX
) on the OnSite Router. Plug the other end
RX
) on the OnSite Router. Plug the other end of
SmartNode 5300 Quick Start Guide
6.0 Complete the installation
To finish configuring your OnSite, and for detailed information about installing, configuring, operating, and trou-
bleshooting, refer to the Models 2603, 2621, and 2635 OnSite Series High Speed Routers User Manual available
online at
www.patton.com/manuals/2600SER.pdf.
A.0 Customer and Technical Support
Toll-Free VoIP support: call
Online support:
www.patton.com
E-mail support: support@patton.com—answered within 1 business day
Telephone support:
6.0
Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to
•
2200 UTC/GMT)
Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800
•
UTC/GMT)
Fax:
+1 (253) 663-5693
B.1 Compliance
EMC:
FCC Part 15, Class A
•
EN55022, Class A
•
EN55024
•
Safety:
UL60950-1/CSA C22.2 No. 60950-1
•
IEC/EN 60950-1
•
AS/NZS 60950-1
•
PSTN Regulatory:
These devices are not intended for connection to the PSTN.
•
SmartNode 5300 Quick Start Guide
with a VoIP SIP phone
sip:support@patton.com
(USA)
or +41 (0)31 985 25 26
(Switzerland)
B Compliance Information
7
Advertisement
