Table of Contents
Advertisement
: no sound effect
: Suitable for genuine speakers
: Suitable for separate
speakers
OlE 3
: Suitable for co-axial speakers
3-3. When the "OlE 1", "OlE 2" or "OlE 3" is
set, push the
[P .CH]
button upward or
downward to change the DZE level from +3
to-3.
*
The factory default setting is "0".
• Adjusting the subwoofer output
volume
You can adjust the volume output from the unit's
subwoofer output terminal.
"S-W VOLUME" can be adjusted only when
"SUB WOOFER" is set to "ST" or "MONO"
(page 19).
2-1.
Select the "S-W VOLUME".
3-1. Push the [P.CH] button upward or .
downward to change the output volume.
*
The factory default setting is "0".
(Setting range: +6 to -6)
• Setting the Digital Z-Enhancer
This unit are provided with
3
types of sound
tone effects stored in memory. Select the one
you prefer.
*
The factory default setting is "DZE OFF".
2-1.
Select the "OlE".
3-1. Press the
[~II
ENT] button.
3-2. Push the [SEEK PANEL] leftward or
rightward to select the tone effect. Each
time you push the [SEEK PANEL], the tone
effect changes in the following order:
"OlE OFF"
+--+
"OlE 1"
+--+
"OlE 2"
+--+
"OlE
3"
OlE OFF
OlE
1
OlE 2
To
change sound mode
SOUND
~
s-w va
UME
When speaker system is "NORMAL":
"S-W VOLUME"
+--+
"OlE"
+--+
"P.EQ"
+--+
"BASS"
+--+
"TREBLE"
+--+
"s
RESTORER"
+--+
"HPF"
+--+
"S-W LPF"
+--+
"BALANCE"
+--+
"FADER"
When speaker system is "3WAY":
"S-W VOLUME"
+--+
"OlE"
+--+
"P.EQ"
+--+
"BASS"
+--+
"TREBLE"
+--+
"s
RESTORER"
+--+
"BALANCE"
When speaker system is "2WAY":
"OlE"
+--+
"P.EQ"
+--+
"BASS"
+--+
"TREBLE"
+--+
"s
RESTORER"
+--+
"BALANCE"
+--+
"FADER"
3. Push the [P .CH] button upward or
downward to select the "desired setting
value".
*
In the case of item names appearing with
the "ENT" suffix after the item name, the
[~II
ENT]
button must be pressed to display
the setting value.
*
"P.EQ" can be adjusted only when the
,"P.EQON/OFF" is set to "ON" (page 19)
and "EQ SELECT" is set to "P.EQ" (page
19).
*
"BASS" and "TREBLE" can be adjusted
only when "DZE" is set to "DZE OFF" (page
12) and "EQ SELECT" is set to "BIT" (page
19).
*
After completing settings, press the [
J' ]
button to return to the previous mode.
Note:
• During sound adjustment mode, if no operation
is performed for more than 10 seconds, this
mode can be canceled and return to the
previous mode.
1. Press the [
J' ]
button and select the sound
mode to adjust.
2. Push the [SEEK PANEL] leftward or
rightward to select the "item
name".
Basic Operations
Adjusting Sound Mode
12
DXZ775USB
Advertisement
Table of Contents
