Basic Operations - Pioneer MVH-1450UB Owner's Manual

Operating this unit
Display indication
1
3 5 7 8 9
2 4 6
Indicator State
! Tuner: band and frequency
! RDS: program service
Main dis-
name, PTY information and
1
play sec-
other literal information
tion ! USB storage device and
iPod: elapsed playback
time and text information
The list function is being oper-
2
(list)
ated.
3 LOC
Local seek tuning is on.
4 (TA) TA function is on.
5 (TP) A TP station is tuned in.
(re-
6
Track or folder repeat is on.
peat)
Random play is on.
(ran-
The iPod source is selected
7
dom/shuf-
and the shuffle or shuffle all
fle)
function is on.
The sound retriever function is
8
(sound re-
on.
triever)
(iPod This unit's iPod function is op-
9
control) erated from your iPod.
Set up menu
When you turn the ignition switch to ON after in-
stallation, set up menu appears on the display.
You can set up the menu options below.
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
2 Turn M.C. to switch to YES. Press M.C. to
select.
# If you do not operate for 30 seconds, the set up
menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO. Press to select.
If you select NO, you cannot set up in the set up
menu.
3 Perform the following procedures to set
the menu.
To proceed to the next menu option, you need to
confirm your selection.
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-
ual tuning.
1 Turn M.C. to select the FM tuning step.
50 (50 kHz)—100 (100 kHz)
2 Press M.C. to confirm the selection.
MW STEP (MW tuning step)
Operating this unit
The MW tuning step can be switched between
9 kHz and 10 kHz. When using the tuner in North,
Central or South America, reset the tuning step
from 9 kHz (531 kHz to 1 602 kHz allowable) to
10 kHz (530 kHz to 1 640 kHz allowable).
1 Turn M.C. to select the MW tuning step.
9 (9 kHz)—10 (10 kHz)
2 Press M.C. to confirm the selection.
DEMO (demo display setting)
1 Turn M.C. to set the demo display to on or off.
2 Press M.C. to confirm the selection.
QUIT appears.
4 To finish your settings, turn M.C. to select
YES. Press to select.
# If you prefer to change your setting again, turn
M.C. to switch to NO. Press to select.
Notes
! You can set up the menu options in the initial
settings. For details about the settings, refer
to Initial settings on page 8.
! You can cancel set up menu by pressing
SRC/OFF.

Basic operations

Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached
to the front panel before detaching it.
Removing the front panel to protect your unit from
theft
1 Press the detach button to release the front
panel.
2 Push the front panel upward (M) and then pull
it toward (N) you.
3 Always keep the detached front panel in a pro-
tection device such as a protection case.
Re-attaching the front panel
1 Slide the front panel to the left.
Make sure to insert the tabs on the left side of
the head unit into the slots on the front panel.
2 Press the right side of the front panel until it is
firmly seated.
If you cannot attach the front panel to the
head unit successfully, make sure that you are
placing the front panel onto the head unit cor-
rectly. Forcing the front panel into place may
result in damage to the front panel or head
unit.
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns
off.
Section
02
3
En