Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Elan vl10
Summary of Contents for Elan vl10
- Page 1 VL10 Tabletop/Under-Cabinet 10” Color Touch Screen INSTALLATION MANUAL ...
- Page 2 17. The power supply cord (sometimes referred to as the Important Safety Instructions “Mains Plug”) is used as the disconnect device and shall remain accessible and operable at all times. 1. Read these instructions. 18. Do not expose batteries to excessive heat such as sunshine, fire or the like.
-
Page 3: Table Of Contents
VL10 ELAN HOME SYSTEMS Table of Contents Introduction ...................... 3 Touch Screen Technology ................ 3 Features ....................... 3 Package Contents ..................... 4 Movable Swivel Display ................ 4 Power Button..................... 6 Mini USB Port .................... 6 Planning ........................ 7 System Wiring ...................... 8 Wiring ........................ 8 Video Termination Switch .............. 9 Under Cabinet Installations .............. 9 Power Supply Options ................ 10 Cable Strain Relief ................... 10 nder Cabinet Installation ................ 11 © ELAN Home Systems 2011 • All rights reserved. Page 2... -
Page 4: Introduction
VL10 is the right choice. Touch Screen Technology The VL10 utilizes a polyester plastic film suspended over a glass panel, which is then adhered to the front of a color LCD (Liquid Crystal Display) screen. Depressing the polyester film with a finger allows the film to touch the glass panel underneath, generating a location signal that is read by the electronics. -
Page 5: Package Contents
Figure 1-1: Package Contents Movable Swivel Display The VL10 display pivots back 90° on a central axis as shown below in Figure1-2, it also pivots forward 45° from its central axis as shown in Figure1-3. The display rotates up to 330° from stop to stop about the vertical axis, allowing you to view the display from almost anywhere in the room as shown in Figure1-3. - Page 6 VL10 ELAN HOME SYSTEMS Figure 1-2: Back to Front Pivoting Display Figure 1-3: Display Rotation © ELAN Home Systems 2011 • All rights reserved. Page 5...
-
Page 7: Power Button
To turn the VL10 off, press and hold the power button for approximately 5 seconds until the VL10 shut downs. The second function is to toggle the back light off and on while the VL10 is in operation. This function can be activated by pressing and releasing the power button. -
Page 8: Planning
The VL10 can be installed and placed on almost any flat surface such as a desk, table or countertop, or easily mounted underneath a cabinet. Because it folds flat, the VL10 can be tucked neatly out of view when not in use. -
Page 9: System Wiring
System Wiring Wiring The VL10 requires power, Ethernet and optionally, video connections. The VL10 comes with a Precision Panel and a 12’ Cable Assembly to simplify the installation. See Figure 3-1 and Figure 3-2 for more wiring details. Figure 3-1: VL10 Wiring Example ... -
Page 10: Video Termination Switch
Figure 3-2: VL10 Precision Panel Wiring Example Video Termination Switch When the video signal coming into the VL10 Touch panel is to be looped back out of the panel to another Touch Panel or TV, an F connector (VIDEO OUT) is provided. The Video Termination Switch must be moved from the factory default to the OPEN position. -
Page 11: Power Supply Options
ELAN HOME SYSTEMS Power Supply Options The VL10 Precision Panel allows for power to be supplied from a remote or a local source. If you choose to power the VL10 locally you will need to purchase a PWR1. Cable Strain Relief The VL10 has a cable clamp system on the underside of the base cover, along the rear edge. -
Page 12: Under Cabinet Installation
VL10 ELAN HOME SYSTEMS Under Cabinet Installation The VL10 is ideal for use installed underneath a kitchen or workshop cabinet. This instruction assumes all pre-wiring has been previously completed. To install VL10 under a cabinet: 1. Choose an appropriate mounting location underneath desired cabinet or shelf. - Page 13 Screw length must protrude from underside of cabinet less than 0.5 inch. See Figure 4-4. 5. Using the provided VL10 Adhesive Backed Vinyl Mounting Template, remove the protective backing material and carefully place the template in position the bottom side of the cabinet. Make sure the arrow on the template is pointing toward the forward edge of the cabinet, as shown below in Figure 4-3.
- Page 14 7. Make the required cable connections (Power, Ethernet and optional Video) to the rear of the VL10. 8. Install the #6-32 screws through the cabinet bottom to the VL10 base. Secure the VL10 to the cabinet by tightening the four screws by hand.
- Page 15 NOTE: A VL10 may replace a previously installed VIA!Valet64 VIA!Valet100 with no modifications to the cabinet. Two extra holes are provided on the base plate of the VL10 that will allow the mounting holes to align exactly when upgrading from a VIA!Valet64.
-
Page 16: Limited Warranty
ELAN in writing, ELAN shall repair or replace the item at the company’s option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been installed by other than an ELAN authorized installer, (c) to installed equipment which is not installed to ELAN’s specifications, (d) to equipment which shall have been repaired or altered...