Advertisement
Advertisement
Table of Contents
Related Manuals for Martin Punisher X250
Summary of Contents for Martin Punisher X250
- Page 1 Destroyer X250 Punisher X250 user manual...
- Page 2 © 1996 - 2001 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000035, Rev. C.
- Page 3 NTRODUCTION The Destroyer X250 and Punisher X250, developed and manufactured by Martin Professional, are aggressive disco lighting effects using a powerful 250W halogen lamp. With a motorized parabolic reflector and gobo wheel, they produce a myriad of turning beams that change color and pattern on demand. There is a “flash”...
-
Page 4: Safety Information
If you have questions about how to operate the fixture safely, please contact a Martin distributor for assistance. To protect yoursel f and others fr om electr ic shock •... - Page 5 To protect yourself and others from injury due to fall s • When suspending the fixture above ground level, verify that the structure can hold at least 10 times the weight of all installed devices. • Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable.
- Page 6 I N S T A L L I N G T H E L A M P See the specifications on page 16 for lamps that may be used in the Destroyer X250 and Punisher X250. Do not install any other lamp. Warning! Allow the unit to cool for 15 minutes before handling.
- Page 7 F I T T I N G T H E M A I N S P L U G The Destroyer/Punisher is delivered from the factory without a plug on the mains cable. You will have to fit a plug that conforms to your local mains outlet. The double insulated mains cable contains three wires.
-
Page 8: F I T T I N G T H E M O U N T I N G B R A C K E T
R E M O V I N G T H E T R A N S P O R T S E C U R I T Y P L A T E ( P U N I S H E R O N L Y ) Before first operating the Punisher, you need to remove the transport security plate inside the unit. -
Page 9: Operation
ONTROLLER PERATION C O N N E C T I N G T H E D A T A L I N K A reliable data connection begins with the right cable. Standard microphone cable cannot transmit DMX data reliably over long runs. For best results, use cable specifically designed for RS-485 applications. - Page 10 Punisher. The 1-channel mode is simpler and saves channels on your controller. In this mode, the unit becomes more aggressive the higher you set the fader. The Martin MC-1 controller is specially designed to operate the Destroy/Punisher and other Martin products is 1-channel mode. When using the Destroyer X250 and Punisher X250 with the MC-1, the address (see below) must be set to DMX channel 1.
- Page 11 A D D R E S S T A B L E Locate the channel in the table below. Follow the row to the left to find the settings for pins 1 to 5; follow the column to the top to find the settings for pins 6 to 8.
- Page 12 TAND LONE PERATION S T A N D - A L O N E If the unit does not receive control data, it automatically goes into stand-alone mode and performs a random sequence triggered by sounds picked up by the built-in microphone.
-
Page 13: M U L T I - C H A N N E L M O D E
DMX P ROTOCOL M U L T I - C H A N N E L M O D E Channel DMX Value Description Lamp ON/OFF 0 - 11 Lamp OFF 12 - 193 Lamp ON Gobo strobe: slow → fast 194 - 255 Trigger Mode 0 - 11... -
Page 14: S I N G L E - C H A N N E L M O D E
Channel DMX Value Description Color/Gobo Wheel 0 - 5 Blackout 6 - 20 Position 1 21 - 36 Position 2 37 -52 Position 3 53 - 68 Position 4 69 - 84 Position 5 85 - 100 Position 6 101 - 116 Position 7 117 - 132 Position 8... -
Page 15: Troubleshooting
ROUBLESHOOTING Problem Probable cause(s) Suggested remedy None of the units respond to The controller is Connect controller. the controller. disconnected from the DMX link. Use of incorrect cable Check pin-out of DMX controller against between the controller and Destroyer/Punisher and ensure that signal + the first unit on the DMX goes to signal + and signal - goes to signal -. -
Page 16: Specifications
PECIFICATIONS P H Y S I C A L Size (L x W x H)....... 340 x 265 x 303 mm (13.4 x 10.4 x 11.9”) Weight ................... 7 kg (15.4 lbs.) T H E R M A L Maximum ambient temperature (T ) ..........