Centre Bar Mounting; Centre Tray Mounting - Quickie Samba 2 Directions For Use Manual

Centre bar mounting

WARNING:
Ensure that all extremities and clothing are free when positio-
ning the centre bar for use.
Always turn off the power to the controller before moving the
controller out of the way.

Centre tray mounting

The tray must be regularly cleaned using a
soapy damp cloth.
Do not use abrasive cleaners or cloths as
they could scuff the surface of the tray.
Do not use solvents.
Make sure that the tray is thoroughly cleaned
regularly, especially if the chair is to be used
by another user.
Fitting:
Affix the mounting tube to the underside of the armrest with
the 2 screws provided. Now slide the extruding bar into the
mounting bracket until it clicks into place (Fig. 46).
WARNING:
The maximum weight allowed for the tray is 2.5kg.
Do not overload the tray; this could cause the tray to break or
could cause the chair to become unstable. Always turn off the
power to the controller before moving the tray out of the way.
Do not leave lit cigarettes or other heat sources on the tray as
this could cause the tray to deform and mark.
Ensure that all extremities and clothing are free when positio-
ning the tray for use.
Swing away tray
Fitting:
Fix the tray table mounting bracket to the
underside of the desired armrest with the
2 fixing screws provided.
Slide the extruding bar into the mounting
bracket until it clicks into place and is secure
(Fig. 47).
WARNING:
The maximum weight allowed for the tray is 2.5kg.
Do not overload the tray, this could cause the tray to break or
could cause the chair to become unstable.
Do not leave lit cigarettes or other heat sources on the tray as
this could cause the tray to deform and mark.
Cleaning instructions:
The tray must be regularly cleaned using a soapy damp cloth.
Do not use abrasive cleaners or cloths as these could scuff the
surface of the tray.
Do not use solvents.
Crutch holder
Using a crutch holder.
Your crutch holder should be fitted by an authorised Sunrise
dealer to the lower section of the push handle. A Velcro strip
should also be fitted to the top section of the push handle and
at relevant position's on your crutch.
Take your crutch and drop it into the cup fitted to the bottom of
the push handle. Line up the Velcro strip on the push handle
and crutch and push together, firmly fixing the crutch to the
chair.
WARNING:
Make sure that the crutch is securely fastened to the crutch
holder.
Make sure that the crutch is not interfering with the mecha-
nisms of the chair.
Make sure that the crutch does not protrude from the chair.
Do not attempt to remove the crutch whilst the chair is in motion.
Always come to a complete stop and turn off the power to the
controls before attempting to remove the crutch. This will avoid
accidentally operating the chair.
14
SAMBA
Rear view mirror
a Rear view mirror Warnings
Always make sure that when using the mirror that it is clean
and unbroken so that it does not impair your visibility.
To avoid injury to people around you please be aware that the
mirror protrudes outside the space envelope of the chair and
could cause injury to someone when driving past.
The mirror must be used on the 10KPH model on UK roads.
Kerb climber
Retrofitting the kerb climber
To retrofit the kerb climber as an optional
Fig. 46
extra you need to take out the bolts of
the height adjustment mechanism. Start
with one side after the other. Procedure:
Take out the bolt of the left hand height
adjustment mechanism by using two 13
mm spanners. Replace the bolt with a
longer one and spacer, as supplied with
the kerb climber retrofit kit. Fit the left
hand kerb climber bracket on the inside
of the bottom frame with the height
adjustment bolt. Screw the second bolt
and spacer through the front hole of the three-point mecha-
nism for height adjustment into the bottom frame. Proceed in
the same way for the right hand bracket (Fig. 48).
Fitting and removal procedure
1. Locate the kerb climber bar into the left hand location
bracket and push it into the right hand receiver bracket.
2. Hold the kerb climber with your right hand in the receiver
bracket.
3. Align the holes of the receiver bracket and the kerb climber
tube and plug in the locking pin from the top.
4. Reverse the procedure to remove the kerb climber.
Fig. 47
Front transfers
If you find that the kerb climber is obstructing your exit or entry
into the wheelchair you can swing the kerb climber back into
the reverse position. Follow the fitting instructions above, but
rotate the climber through 90° backwards.
The kerb climber must be returned to its operating position
prior to climbing kerbs.
Mounting the kerb or step
1. Approach the kerb (step) head on
driving forwards slowly and steadily
and always at a 90° angle (Fig. 49).
2. As the Kerb Climber makes contact
with the kerb (step), the wheelchair
should be moving slowly. Small
kerbs can be climbed from a stand-
still.
3. Apply sufficient power to the motors
to lift the front of the chair up onto
the kerb (step) and then apply
slightly more power and speed so
that the drive wheels climb the kerb (step) smoothly and
without hesitation. As far as possible, keep the joystick in
the straight forward position.
4. In accordance to the ground clearance, the maximum
obstacle height possible to pass is 50 mm (100 mm with
kerb climber).
Fig. 48
Fig. 49
Rev.A 0807/2000/ST/000690635.EMS