Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hyundai HY55200-3
Summary of Contents for Hyundai HY55200-3
-
Page 2: Table Of Contents
CONTENTS PARTS INTRODUCTION ELECTRICAL NOTES INSTALLATION 5/6. START UP 6/7. MAINTENANCE 7/8/9. PRESSURE SWITCH ADJUSTMENTS 9/10. ELECTRICAL CONNECTIONS 10/11. SPECIFICATIONS DECLARATIONS of CONFORMITY RECYCLING PAGE 2... -
Page 3: Parts
1. PARTS. PAGE 3... -
Page 4: Introduction
The “Warning” notes, underline those operations which, if not carried out correctly could cause damage to the equipment and injury to the user. We strongly recommend only genuine Hyundai replacement spare parts are used, which will guarantee the efficiency and service life of the compressor. -
Page 5: Electrical Notes
3. ELECTRICAL NOTES. 3.3 Always use a qualified electrician to connect the compressor to the mains. Check electrical supplies match compressor specification as per the motor information plate (fig 6). 3.4 All compressors are supplied with a power cable of 2 metres for connection to a fused isolator close to the compressor. -
Page 6: Start Up
CAUTION Never use the ground clamp in place of the neutral clamp to provide a single phase supply. Earthing connections must be carried out in accordance with the safety regulations (EN60204). The power cable plug or socket/isolator must not be used to stop the compressor, as this could cause damage to the compressor when restarting. -
Page 7: Maintenance
Thoroughly clean all external parts of the compressor and motor every 6 months or 2000 running hours to ensure proper cooling. 6.3 Oil. Check oil level every day (Fig. 3) when compressor is cold, top up as necessary. Use Hyundai 100 OIL or SAE10W/30 engine oil. 6.4 Oil change. - Page 8 6.5 Emergency STOP button (TANDEM ONLY ) . The emergency stop button (Fig17) is located on the wall-mounted starter this allows the compressor to be stopped in an emergency. DO NOT USE THIS SWITCH AS A POWER SWITCH. To reset the emergency button, rotate the red knob anti-clockwise a half turn. To restart the compressor refer to “START UP”...
-
Page 9: Pressure Switchadjustments
Compressed air receivers for the European market are built in accordance with EC Directive 09/105. Air Compressors for the European market are built in conformity with the Directive 2006/42/EC 7. PRESSURE SWITCHADJUSTMENTS. NE-MA Single Phase N.B. Warning Switch off power at fused isolator before making any adjustment to the pressure-switch. 7.1 NE-MA pressure switch is supplied with a standard cut out pressure 150 psi and a cut in pressure of 120 psi. -
Page 10: Electrical Connections
MDR-3 Three Phase N.B. Warning Switch off power at fused isolator before making any adjustment to the pressure-switch. MDR-3 pressure switch is supplied with a standard cut out pressure 150 psi and a cut in pressure of 120 psi. Both these settings can be adjusted to suit your individual requirement as follows: 7.4a Increase or decrease cut out pressure. - Page 11 STAR DELTA 400/50/3 TANDEM STARTER CIRCUIT DIAGRAM 230/50/1 PAGE 11...
-
Page 12: Specifications
1600 x 500 x 1040 Net Weight - kg Tank material Rolled steel Rolled steel 10. DECLARATIONS of CONFORMITY. Compressor models HY55200-3 & HY75270-3 Designed & produced in accordance with the following • Machinery Directive 2006/42/EC Supply of Machinery (Safety) Regulations 2008 • •... - Page 13 11. DECLARATIONS of CONFORMITY. Products which are labelled with the adjacent symbol MUST NOT be disposed of in household rubbish. You must dispose of packaging and old electrical and electronic equipment separately. 11.1 Disposing of packaging. 10.1.1 The packaging consists of cardboard and correspondingly marked plastics that can be recycled.
- Page 14 NOTES PAGE 13...
- Page 15 NOTES PAGE 14...
- Page 16 GENPOWER LTD Isaac Way, Pembroke Dock, Pembrokeshire, UK, SA72 4RW T: +44 (0) 1646 687880 F: +44 (0) 1646 686198 sales@genpower.co.uk www.hyudaipowerequipment.co.uk...