Related Manuals for Queclink GL100
Summary of Contents for Queclink GL100
-
Page 1: User Guide
GL100 GSM/GPRS/GPS Tracker User Guide TRACGL100UM002 Revision: 2.03 http://www.queclink.com sales@queclink.com... - Page 2 TRACGL100UM002 General Notes Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers. Queclink has not undertaken any independent search for additional relevant information, including any information that may be in the customer’s possession.
-
Page 3: Table Of Contents
3.2. Battery Charging .........................9 3.3. Install SIM Card ........................10 3.4. Turn on/Turn off ........................10 3.5. Operating on function key....................10 4. GL100 Manager Setup Wizard ....................11 4.1. Main setting........................11 4.2. The main window......................12 4.3. Protocol Commands History .....................13 4.4. An example to configure GL100 ..................14 4.4.1. -
Page 4: Revision History
GL100 User manual 0. Revision history Revision Date Author Description of change 2.01 2009-08-07 Moon XIE Initial 2.02 2009-12-09 Ella HUANG Update parameters of special function in chapter 4.4.5 2.03 2010-11-03 Ella HUANG 1. Add Chapter 4.4.8 and 4.4.9; 2. Update parameters of real time operation in chapter 4.4.7. -
Page 5: Introduction
GL100 User manual 1. Introduction GL100 is a powerful GPS locator which is designed for vehicle, pets and asserts tracking. With superior receiving sensitivity, fast TTFF and GSM frequencies 850/900/1800/1900. Its location can be real time or schedule tracked by backend server or specified terminals. Based on the... -
Page 6: Product Overview
2.1. Appearance 2.2. Buttons/Mini USB Interface Description Button /Mini USB Interface Description Power Key Turn on GL100 Turn off GL100 (If power key is enabled). Function Key Geo-Fence mode (default) Press the key twice in 2 seconds to enable/disable Geo-Fence0... -
Page 7: Two Triple-Color Leds Description
There are two triple-color LEDs in GL100. Each LED shows red, green and blue to indicate different state of GL100. For better understanding, we call them Red LED 1, Green LED 1, Blue LED 1 and Red LED 2, Green LED 2, Blue LED 2. - Page 8 GL100 User manual SOS mod The blue led2 will be solid when the function key is pressed. It will be off after the function key released. User should press the function key for at least 3 seconds to start SOS report.
-
Page 9: Getting Started
AC-DC Power Adapter It is used to charge the internal (Standard accessory) battery of GL100. GL100 Sheath It is used to attach the GL100 to (Standard accessory) belt. Screw Driver It is used to twist off/ tighten the (Standard accessory) two screws on the side of GL100 when install SIM card. -
Page 10: Battery Charging
During charging, the Red LED 2 is blinking slowly. When the battery is full charged, the Green LED 2 will be solid. You can also charge the battery by USB cable which connects GL100 with the PC. Charging time is about 5 hours. -
Page 11: Install Sim Card
3.4. Turn on/Turn off Turn on: Press the Power key at least 3 seconds and release it to turn on GL100. At the same time, Red LED 1 will light on for 2~3 seconds. Then Green LED 1 starts to blink quickly which means searching the GSM network. -
Page 12: Gl100 Manager Setup Wizard
GL100 manager tool is PC software which can be used to configure GL100 through Data_Cable. It is easy for the backend server developers to configure GL100 with manager tool, which has friendly user interface. The correct command messages sent to GL100 will be displayed on the manage tool.(These messages can also be sent by SMS or GPRS ). -
Page 13: The Main Window
“Send All” is used to send the configuration message which is enabled in zone “Function setting” “Read All” is used to read all the parameters from GL100 and display in zone “Function setting” [Config]: Include “Main Setting”, “Save Config File” and “Load Config File”. -
Page 14: Protocol Commands History
Display the state of operation, including the serial port state, baud rate state, and the operation result. Function setting Set and view the parameters of the functions. 4.3. Protocol Commands History The Protocol Commands History Dialog shows all the commands which have been sent to GL100 from the Manager Tool. TRACGL100UM002 - 13 -... -
Page 15: An Example To Configure Gl100
GL100 User manual 4.4. An example to configure GL100 The manager tool is developed based on the @Track Air Interface Protocol. Please refer to “GL100 @Track Air Interface Protocol” for detail. Following is a general procedure to configure GL100 with manager tool. -
Page 16: Set The Parameters Of Secondary Backend Server
GL100 User manual In the “Main SMS Gateway” text box, input the phone number of main SMS gateway which is used to receive the message from GL100 by SMS. The international format like “+8615201772961” and short code like “10086” are both supported. -
Page 17: Set The Parameters Of Scheduled Fixed Timing Report
GL100 through SMS or GPRS. Step_3: It is recommended to read the parameters from GL100 and edit based on them. Step_4: Set the “Start Time”, the value range of “HH” is “00”-“23”. The value range of “MM” is “00”-“59”. -
Page 18: Set The Parameters Of Geo-Fence
Step_2 Step_4 Step_1: User can define up to five Geo-Fence regions on GL100. Each region is a circular area which is defined by central coordinate and radius. When the device enters or leaves a predefined Geo-Fence region, GL100 will send alert information to server. -
Page 19: Set The Parameters Of Special Function
GL100 User manual be sent to GL100 through SMS or GPRS. Step_3: It is recommended to read the parameters from GL100 and edit based on them. Step_4: Click the “Send” button; download the parameters of GTGEO to GL100. 4.4.5. Set the parameters of special function... -
Page 20: Set The Parameters Of Synchronization Ack Setting
GL100 User manual Step_6: Set the mode of function key. Please refer to “GL100 @Track Air Interface Protocol” for detail. Step_7: Set the parameters of movement detection function. Please refer to the “GL100 @Track Air Interface Protocol” for detail. Step_8: “Fully Power Up By Charger”: If selected, GL100 will enter normal power-on mode even when it is powered on by charger. -
Page 21: Real Time Operation
GL100 User manual message is sent through the connection specified by “Ack Type”, GL100 will wait for the Synchronization ACK message. Otherwise, GL100 won’t wait for the Synchronization ACK message. Please refer to “GL100 @Track Air Interface Protocol” for detail. - Page 22 Choice 9 is used to set the parameters of over speed alarm. “Speed Alarm Enable”: Disable or enable the over speed alarm function “Speed Alarm Value”: When the over speed alarm function is enabled, GL100 will report to the backend server when its speed is larger than this value.
- Page 23 GL100 User manual Choice C is used to configure the terminal to periodically report the information. (ICCID, GSM signal level, battery level and the status of charging). “Info reported period”: 0 means disable report the terminal’s information; 1-1440 means the period of reporting, and the unit is minutes.
- Page 24 “Event Mask”: A numeric in hex style to mask the report message. One bit represents a message. Click “Set Even Mask”, and select which message type you want to report by terminal in pop box. Step_4: Click the “Send” button; download the parameters of GTRTO to GL100. TRACGL100UM002 - 23 -...
-
Page 25: Set The Parameters Of Google Link Function
Step_5: Set google link name. Please refer to the “GL100 @Track Air Interface Protocol” for detail. Step_6: Set the mobile index from start to end which you want to edit. Please refer to “GL100 @Track Air Interface Protocol” for detail. -
Page 26: Set The Parameters Of White Call List
GL100 through SMS or GPRS. Step_3: It is recommended to read the parameters from GL100 and edit based on them. Step_4: Set call filter enable or disable in white call list function. Please refer to “GL100 @Track Air Interface Protocol” for detail. -
Page 27: Troubleshooting And Safety Info
It is better to let the top surface face to sky. (The same surface with indication LED) GL100 will stop GPS if it can’t get GPS fixing in 2 minutes (except in emergency mode). So please make sure the GPS... -
Page 28: Safety Info
Please do not put the device on the overheating or too humid place, avoid exposure to direct sunlight. Too high temperature will damage the device or even cause the battery explosion. Please do not use GL100 on the airplane or near medical equipment. TRACGL100UM002...