Installation And Removal Of Exhaust Hose - Sharp S3503CVP09FX/T Service Manual

Installation in a sliding sash window
(See page 12 for installation in a double-hung window.)
1
Connect the rain guards to the insect
guard net.
Insert all three projections on each rain
guard into the holes in the insect guard net.
Side "A" will now be uppermost, as
indicated in the diagram.
2 Attach the guard combined above to the
window panel.
Push the insect guard net firmly to ensure
that its four projections fit into the holes in
the window panel.
Side "A" will now be at the top, as indicated
in the diagram, when it is installed in the
window.
3
Cut the foam seal A (adhesive type) to the
proper length and attach it to the window
frame.
4 Install the window panel into the window
frame.
If the inner height of the window is
between 22" (559mm) and 24" (609mm)
inclusive.
The window panel cannot be installed in
windows less than 22" (559mm) high, as
you will be unable to shut the exhaust
cover.
(1) Remove the adjustment panel from the
window panel, and cut the window panel
to the same height as the window.
(2) Open the window sash and place the
window panel on the window frame.
(3) Secure the window panel to the window
frame with 2 screws.

[5] INSTALLATION AND REMOVAL OF EXHAUST HOSE

The exhaust hose must be installed or removed in accordance with the usage mode.
MODE
COOL, FAN, VENTILATION, DEHUMIDIFICATION with no container
DEHUMIDIFICATION with container(minimum capacity 3 gallons)
Installation of the exhaust hose
1 Attach the window exhaust adapter to
the exhaust hose.
Extend one end of the exhaust hose and
insert it into the window exhaust adapter,
and turn it (approx. three times) until it
stops.
Make sure they are securely attached
afterwards.
2 Attach the exhaust hose adapter to the
unit.
Insert the two projections on the exhaust
hose adapter into the two holes on the
unit, and firmly attach them to each
other.
3 Slide and open the exhaust cover on
the window panel, and attach the win-
dow exhaust adapter.
Surface of window exhaust adapter
marked "TOP" should be at the top when
it is installed in a double-hung sash
window.
Surface of window exhaust adapter
marked "TOP" should be on the window
frame side when it is installed in a sliding
sash window.
The exhaust hose should be as short as possible for operational efficiency;
however, it must not be twisted or bent.
Unacceptable
Insect guard net
Hole
Projection
Window panel
"A"
Projection
Foam seal A
(adhesive type)
Exhaust cover
Window
panel Cut
Adjustment panel
Window
panel
22"~24"
EXHAUST HOSE
Install
Remove
Extend
Exhaust hose
Acceptable Acceptable
If the inner height of the window is
between 24" (609mm) and 36.8"
(934mm) inclusive.
"A"
(1) Open the window sash and place the
window panel on the window frame.
(2) Slide the adjustment panel to fit the
window frame height.
(3) Secure the window panel to the window
frame with 3 screws.
Rain guard
If the inner height of the window is be-
tween 36.8" (934mm) and 48" (1219mm)
inclusive.
(1) Attach the extension panel to the
adjustment panel.
(2) Open the window sash and place the
window panel on the window frame.
(3) Slide the adjustment and extension
panels to fit the window frame height.
(4) Secure the window panel to the window
frame with 4 screws.
5
Cut the foam seals (adhesibe type) A and
B to the proper length and attach them to
the window panel.
Attach foam seal A to the window panel and
extension panel, and attach foam seal B to
the adjustment panel.
6 Close the window sash securely against
the Window panel.
7
Cut the foam seal to an appropriate length
and seal the opening between the side of
the inner window sash and the outer win-
dow sash.
8 Attach a bracket with the screw.
Removal of the exhaust hose
1 Remove the window exhaust adapter.
Pull out and remove the window exhaust
Window
adapter by pushing down two
exhaust
markings, and slide and close the exhaust
adapter
cover in the window panel.
2 Remove the exhaust hose adapter from
the unit.
Lift up and remove the exhaust hose
adapter from the unit by pushing down on
the two projections.
Projection
Hole
"TOP"
2 – 4
CVP09FX
Adjustment
panel
24"~36.8"
Extension panel
36.8"~48"
Foam seal B
(adhesive type)
Foam seal A
(adhesive type)
Bracket
Foam seal
"PUSH"
"PUSH"
Projection