Drainage; Maintenance - Sharp S3503CVP09FX/T Service Manual

CVP09FX
9. Timer operation
9.1. Off timer
The unit will turn off automatically according to your setting.
Timer duration can be set from a minimum of half an hour (30 minutes) to a
maximum of 12 hours.
Up to 9.5 hours, you can set in half-hour (30-minutes) increments and from 10 to 12
hours, in 1-hour increments.
Point the remote control at the signal receiver win-
dow on the unit.
1
Press the OFF TIMER button and set the time
as desired.
• The time setting will change as you press the
Hold the button down to speed through the set-
tings.
• The orange TIMER lamp on the unit will light.
• The unit will emit a beep when it receives the
1
• The time setting will count down to show the re-
Press the CANCEL button.
• The orange TIMER lamp on the unit will turn off.
Display shown when you
set the unit to turn off 2.5
hours later.
NOTES ON TIMER SETTING AND OPERATION
• The latest time setting will be memorized and will appear on the remote control display the next
time you set the OFF TIMER or ON TIMER.
• The OFF TIMER and ON TIMER can not be set together.
Only the most recent TIMER setting will be valid.
• While the ONE-HOUR OFF TIMER is set, the OFF TIMER and ON TIMER is settings are
unavailable.
• If the ONE-HOUR OFF TIMER is set while the OFF TIMER or ON TIMER activated, the ON
TIMER or OFF TIMER setting will be cancelled.
• If a power failure occurs while the OFF TIMER or ON TIMER is set, the TIMER setting will be
cancelled and will not be retrieved even after the power is restored.
9.2. On timer
The unit will turn on automatically according to your setting.
Timer duration can be set from a minimum of half an hour (30 minutes) to a
maximum of 12 hours.
Up to 9.5 hours, you can set in half-hour (30-minute) increments and from 10 to 12
hours, in 1-hour increments.
Point the remote control at the signal receiver win-
dow on the unit.
1
Press the ON TIMER button.
• The time setting will change as you press the button
Hold the button down to speed through the set-
tings.
• The orange TIMER lamp on the unit will light.
1
• The unit will emit a beep when it receives the signal.
• The time setting will count down to show the re-
Select the mode, temperature, fan speed setting
and PLASMACLUSTER operation as desired.
• When the temperature is set with the ON TIMER,
• If you do not change the setting, the unit will operate
TO CANCEL TIMER
Display shown when you set
Press the CANCEL button.
the unit to turn on 6.5 hours
later. • The orange TIMER lamp on the unit will turn off.
10. Auxiliary mode
Use this mode when the remote control is not available.
1
1
Press the AUX. button again.
NOTES:
• The red OPERATION lamp on the unit will turn off.
• If the AUX. button is pressed during normal operation, the unit will turn off.
• Upon starting AUXILIARY operation, the drainage pump inside the unit runs for
about a minute, which may produce an audible gurgling sound.
button as follows.
0.5h 1.0h 1.5h 10h 11h 12h
signal.
maining time.
TO CANCEL TIMER
as follows.
0.5h 1.0h 1.5h 10h 11h 12h
maining time.
the temperature will show in the display for 5 sec-
onds and then return to the time display.
using the most recent setting.
Press the AUX. button on the unit.
• The red OPERATION lamp on the unit will
light and the unit will start operating in COOL
mode.
• The fan speed is set to AUTO.
• The temperature setting is automatically set
according to the room temperature.
TO TURN OFF

[8] DRAINAGE

Prepare for drainage and drain out water within the unit in the following cases.
If the unit stops operating and the TIMER, OPERATION and MEGA COOL lamps are
blinking. (This indicates that the water tank inside the unit is full.)
1 Make sure to turn the unit off.
2 Turn the drainage nozzle to the OPEN
position.
3 Pull the stopcock out from the drainage
nozzle.
• When the stopcock is removed, a small amount of
water may be discharged from the drainage nozzle.
4 Insert the hose clamp into a standard
commercially available hose (5/8" inner
diameter, 7/8" outer diameter) and attach
the drain gromment to the hose.
5
Attach the hose to the drainage nozzle, and
secure it with the hose clamp.
• Prepare for draining, as drain water will come out
through the hose during operation.
6 Press the AUX. button on the unit twice.
• The water will drain out through the drainage hose.
Maximum amount of water that may be drained
out is approximately 4 1 /
• The OPERATION, TIMER and MEGA COOL
lamps will be blinking.
7
When drainage water stops running out from the hose, turn the unit off by
pressing AUX. button.
• This would take about one minute.
8
Remove the hose from the drainage nozzle, and replace the stopcock.
• Keep the hose clamp and drain grommet in case of re-used.
9 Turn the drainage nozzle to the CLOSE position.
Whenever the unit is moved (to provent water within the unit from spilling).
When the unit is not used for a long time.
1 Carry out the above procedures from 1 to 5.
2 Press the AUX. button on the unit.
• The water will drain out through the drainage hose.
Maximum amount of water that may be drained out is approximately 4
• The OPERATION lamps will light.
3
When drainage water stops running out from the hose, turn the unit off by
pressing AUX. button.
• This would take about one minute.
4
Remove the hose from the drainage nozzle, and replace the stopcock.
• Keep the hose clamp and drain grommet in case of re-used.
5
Turn the drainage nozzle to the CLOSE position.
6 Remove the stopcock from the drainpipe nozzle, and completely drain any
water within the unit.
• Always prepare a receptacle to collect the water
before draining. Maximum amount of water that
may be drained out is approximately
7
Replace the stopcock to the drainpipe nozzle.

[9] MAINTENANCE

Be sure to disconnect the power from the wall socket before performing any mainte-
nance.
CLEANING THE FILTERS
If the filter is clogged with dust, the airflow will be reduced, resulting in poor cooling perform-
ance. The filter should be cleaned every two weeks.
CLEANING THE UNIT AND THE REMOTE CONTROL
Wipe them with a soft, dry cloth or with a cloth moistened with a mild soap. Carefully remove
any residue by wiping with a damp cloth and dry completely.
Avoid splashing water onto the unit. Water can dangerously damage the electrical insulation.
Never use harsh chemicals or abrasive cleaners on any part of the unit. To avoid damaging the
unit, do not use hot water (120°F/50°C or hotter) when cleaning.
CLEANING THE INSECT GUARD NET
Insect guard net
MAINTENANCE AFTER AIR CONDITIONER SEASON
1
Perform drainage to drain out water within the unit. (See Page 29 "When the unit is not
used for a long time").
2
Operate the unit the FAN or VENTILATION mode for about half a day to thoroughy dry
inside the unit.
3
Clean the filters, then reinstall them.
2 – 7
"OPEN" position
pints.
5
Hose
1 /
5
2 / pints.
5
Drainpipe nozzle
1
REMOVE THE FILTERS
• Gently pull the filter handle to the right and slide
the filter out of the unit.
2
CLEAN THE FILTERS
• Use a vacuum cleaner to remove any dust. If the
filters are very dirty, wash them with detergent and
rinse carefully with clean water. Dry the filters in
the shade before reinstalling them.
Filters
3
REINSTALL THE FILTERS
• Hold the filter handle and gently push the filter back
into place.
Never operate the unit without the filter. Doing so
may result in serious damage to the unit.
The cooling performance may be reduced or stop
completely if the insect guard net becomes clogged
with dust.
Periodically remove the window exhaust adapter from
the window panel and clean the insect guard net with a
vacuum cleaner or suchlike.
Drainage
nozzle
Stopcock
Drain grommet
Hose clamp
pints.
Stopcock