Panasonic KX-VC300 Operating Instructions Manual page 113

(This mode switches the display resolution
according to the condition of the network.)
–
"Auto" (default [for KX-VC600]): This mode
selects either "Full HD" or "HD" according to
the available bandwidth.
Note
•
Selecting "Auto" or "HD" is recommended.
•
If you are using the KX-VC300, "Auto" or
"Full HD" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 107).
•
When "Full HD" is selected, if the other
party has a low bandwidth, the display
resolution may be lower than when "HD" or
"Auto" is selected.
•
When making a 3-party video conference
call, the main video camera will be
automatically set to "HD", even if you have
specified "Full HD".
•
When making a 4-party video conference
call, the main video camera and sub video
camera will be automatically set to "HD",
even if you have specified "Full HD".
•
When "Video Quality" is set to
"Sharpness", only "Full HD" and "Auto"
can be selected.
"SIP Transport Protocol": Use [
between protocols (UDP, TCP, or Auto [default])
used when communicating via SIP.
Note
•
When "Auto" is selected, if using a SIP
server, TCP will be used for
communication, and if using an IP address
or MCU's conference room number@IP
address, UDP will be used for
communication. Normally, select "Auto".
"IP Address": Use [
IP address information for the local site ("IP
Address", "Subnet mask", "Default Gateway")
will be obtained automatically from a DHCP server
or will be set manually.
–
"Auto": Obtain the IP address information
automatically.
–
"Manual" (default): Set the IP address
information manually.
Note
•
Even if you have selected "Auto", you still
may not be able to acquire an IP address
due to problems such as network
Document Version 2012-03
][ ] to select
][ ] to select whether the
congestion. In this case, "Address is not
assigned" is displayed in the upper right of
the Home screen. Contact your network
administrator.
"IP Address": Enter the IP address for the local
site.
"Subnet mask": Enter the subnet mask.
"Default Gateway": Enter the IP address of the
default gateway.
Note
•
"IP Address", "Subnet mask", and
"Default Gateway" can be entered only if
"IP Address" is set to "Manual".
•
If the value for "IP Address", "Subnet
mask", or "Default Gateway" contains 1 or
2 digits numbers, enter these numbers as
they are. Do not enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
"DNS Server": Use [ ][
IP address information for the DNS servers
("Primary DNS Server", "Secondary DNS
Server") will be obtained automatically from a
DHCP server or will be set manually.
–
"Auto": Obtain the IP address information
automatically.
–
"Manual" (default): Set the IP address
information manually.
Note
•
To select "Auto", "IP Address" must be
set to "Auto".
"Primary DNS Server": Enter the IP address of the
primary DNS server.
"Secondary DNS Server": Enter the IP address of
the secondary DNS server.
Note
•
"Primary DNS Server" and "Secondary
DNS Server" can be entered only if "DNS
Server" is set to "Manual".
•
If the value for "Primary DNS Server" or
"Secondary DNS Server" contains 1 or 2
digits numbers, enter these numbers as
they are. Do not enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
"SIP Server": Use [ ][
"OFF" (default).
Contacts and Settings
] to select whether the
] to select "ON" or
Operating Manual 113