Advertisement
Quick Links
Advertisement
Related Manuals for Contura C26K High
Summary of Contents for Contura C26K High
- Page 1 Installation instructions C26K High www.contura.eu...
- Page 2 See rating plate on the stove Intended area of use Heating of rooms in residential buildings Fuel Wood MANUFACTURER Name NIBE AB / Contura Address Box 134, Skulptörvägen 10 SE-285 23 Markaryd, Sweden CHECKS According to AVCP System 3 European standard...
-
Page 3: Table Of Contents
A warm welcome to the Contura family. We hope you will get a great deal of pleasure from your new stove. As a new owner of a Contura stove, you have secured a product with timeless design and long service life. -
Page 4: Technical Details
This manual contains instructions on and chimney. The stove and chimney can how the stoves must be assembled and Model C26K High usually be placed on a normal wooden joist installed. To ensure the function and Weight (kg) 240*... -
Page 5: Supply Of Combustion Air
SUPPLY AIR/ACCESSORY Supply of combustion air When a stove is installed in a room, the air supply demand to the room increases. Air can be provided indirectly via a vent in the outer wall or via a duct from the outside that is connected to the connector on the underneath of the stove. -
Page 6: Connection To Chimney
If further sealing material is required, heat- resistant sealant may be used. Sweeping When sweeping, the smoke baffle must be removed; on the Contura 20 series this is easily done by lifting and then pushing the baffle to the side. -
Page 7: Installation Distances
INSTALLATION DISTANCES Installation distances C26K High A = height from floor to chimney connection upwards Place the stove on the hearth B = height from floor to c/c chimney connection rear plate and check that the C = distance from back to c/c chimney connection upwards... -
Page 8: Installation Of C26K High
ASSEMBLY Installation of C26K High The stove needs to be placed on a level and horizontal surface, so the courses do not end up uneven and crooked. Otherwise, this can result in abnormally large gaps and uneven lines. During assembly, check that all tiles stand horizontally and that all parts in a course are of a uniform height. - Page 9 MONTERING ASSEMBLY Place the profile edge to edge with the tile's side.
- Page 10 ASSEMBLY Wait to tighten this screw until the next tile is in place.
- Page 11 ASSEMBLY When installing the two upper courses: Wait to tighten the screws in the tile until all parts are in place and all adjustments have been made. Prevent the side panels from dipping forward by hooking the hooks in the rear profile and tightening the screws until they engage...
- Page 12 ASSEMBLY Not with the heat reservoir option...
- Page 13 ASSEMBLY The front plates are moved up slightly by hooking the hooks in the rear profile and tightening the screws. Tighten the screws until the upper plates align with the upper edge. Tighten all screws in the tiling. For the heat reservoir option, go to page 79 Final inspection of the installation It is extremely important that the installation is inspected by an authorised chimney sweep before the stove is used.
-
Page 14: Final Installation And Joining
ASSEMBLY Final installation and joining Adjustment screws for placement in the guide plate to support the top plates. Adjust them, so they are at the same height as the top of the side plates. Open and fold out any deformed edges in the pipe opening to facilitate installation. -
Page 15: Installation Of Heat Reservoir(Option)
ASSEMBLY Check that the damper can be opened and closed without problem. Installation of heat reservoir(option) Go to page 78 for final installation and joining... - Page 16 NIBE AB · Box 134 · SE-285 23 Markaryd · Sweden www.contura.eu Contura reserves the right to change colours, materials, dimensions and models at any time without special notice. 811092 IAV SE-EX C26K Hög -5 Your dealer can give you the most up to date information.