Download Print this page

Advertisement

Operating and Installation
Instructions
Induction Wok
CS 1223
en - CA
To prevent accidents and
machine damage,
read the Operating Manual
before
installation or use.
M.-Nr. 07 353 931

Advertisement

   Summary of Contents for Miele CS 1223

  • Page 1

    Operating and Installation Instructions Induction Wok CS 1223 en - CA To prevent accidents and machine damage, read the Operating Manual before installation or use. M.-Nr. 07 353 931...

  • Page 2: Table Of Contents

    Contents Warning and safety instructions ........3 Description of the unit .

  • Page 3: Warning And Safety Instructions

    All other types of use are not permitted. Miele cannot be held liable for damage Keep these operating instructions in resulting from incorrect or improper a safe place and pass them on to use.

  • Page 4

    Warning and safety instructions Children Packing materials (e.g., foil, Styrofoam) can be dangerous for Activate the Child Safety Lock so children, Danger of suffocation. Ensure that children cannot turn the wok on that any packing material is disposed of inadvertently. safely and kept out of the reach of Always supervise any children in the children.

  • Page 5

    Installation, maintenance or repair work operate a damaged appliance. A by unqualified persons could pose damaged appliance is dangerous and serious risks to the user for which Miele poses a safety hazard. will not be held liable. The electrical safety of the induction...

  • Page 6

    A wok pan that has boiled dry can be held liable for damages resulting cause damage to the ceramic surface from improper installation or for which Miele cannot be held liable. connection. Overheated oil or fat could ignite and spark a fire.

  • Page 7

    Warning and safety instructions Protect your hands when working NEVER place hot pots or pans near around the hot wok - wear the display. That could damage the heat-resistant oven mitts and use electronic unit underneath. potholders, etc. Use only dry Be careful that no objects or potholders, make sure they are not cookware fall onto the ceramic surface.

  • Page 8

    Warning and safety instructions If there is a drawer below the wok, Miele cannot be held liable for do NOT store any spray cans, damage caused by failure to comply flammable liquids, or other flammable with these safety instructions and materials in the drawer.

  • Page 9: Description Of The Unit

    Description of the unit a Wok burner C 11 " (30 cm) e Display Rating in watts: 2400 W ß with Booster: 3200 W No wok on burner b Wok pan (included) Auto-heat c Control knob Fault (see "Frequently asked questions") d Indicators C / 0 Safety cut-out feature...

  • Page 10: Before Using For The First Time

    Before using for the first time Start-up Attach the data plate found in the documents for your appliance in the When the induction wok is first locations indicated in "Data Plate." connected, and after a power failure, all of the indicators in the display will light up for approx.

  • Page 11: Induction

    Induction How it works Be careful not to place cutlery or An induction coil is located under the other metal objects on the combiset. burner. When the burner is switched When the appliance is switched on, on, this coil creates a magnetic field or when there is residual heat which impacts directly on the base of present, there is the risk of metal...

  • Page 12: Noises

    Induction Noises Cookware The following noises can occur when Only the wok pan supplied should be the induction wok is in use. used with this appliance. The wok pan is designed specifically for this – Higher power settings may cause a induction wok.

  • Page 13: Use

    Turning the combiset On/Off Residual heat indicator The residual heat indicator will go out Do not leave the appliance once the combiset has cooled to a safe unattended while in use. temperature. As long as the residual heat To turn the combiset on turn the control indicator is lit do not touch or place knob clockwise a to the desired any heat sensitive items on the...

  • Page 14: Settings

    Settings When Auto-heat has been activated, the burner switches on automatically at Use for Power the highest setting and then switches to level the continued power level which was selected. The "heat-up" time depends Keeping food warm, 1 - 2 on which continued power level has Melting chocolate, etc.

  • Page 15: Booster Function

    Booster function Activating the booster function ^ Turn the control knob past power The induction wok is equipped with a booster function to temporarily increase level 9 to BI, then back to 9. the power level. When the Booster is I appears in the display and the B activated the burner will operate at indicator lights up.

  • Page 16: Safety Features

    Safety features Child Safety Lock Safety cut-out The combiset has a safety cut-out Keep children away from the feature in case it is not turned off after combiset for their own safety. use. The combiset has a Child Safety Lock If the burner is heated for an unusually to prevent children from turning on the long period of time (see table), and the...

  • Page 17: Overheating Protection

    – If the temperature still continues to rise after the power level has been If the overheating protection feature reduced, the appliance will switch off triggers again, contact Miele Technical and an H will appear in the display. Service. ^ Turn the control knob to "0".

  • Page 18: Cleaning And Care

    Cleaning and care To avoid damage to the surfaces do Do not use a steam cleaning not use any appliance to clean the induction – cleaning agents containing soda, wok. The steam could reach the ammonia, alkaline, acid or chloride, electrical components and cause a short circuit.

  • Page 19

    Remove coarse soiling with a damp cloth. Stubborn soiling is best removed with a glass scraper. Stainless steel Next, clean the wok with the Miele Use a ceramic and stainless steel ceramic and stainless steel cleaner cleaner to clean stainless steel surfaces (see "Optional accessories"), or a...

  • Page 20: Frequently Asked Questions

    What if F and 01 flash alternately in the display? Possible fault Solution The control knob is either damaged or If this is not the case contact Miele stuck. Technical Service. What if F and a number flash alternately in the display?

  • Page 21

    Frequently asked questions What if the combiset turns itself off automatically? Possible fault Solution Either the "Safety cut-out" feature or the See "Overheating protection" or "Safety "Overheating protection" feature has cut-out". been activated. What if one of the following errors occurs: - The booster function turns off automatically ahead of time.

  • Page 22: Technical Service, Data Plate

    Technical Service, Data Plate In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance.

  • Page 23: Installation Instructions

    Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use.

  • Page 24: Safety Instructions For Installation

    The cooktop must not be installed over a refrigerator or freezer, dishwasher, washer or dryer. Do not install this appliance above a Miele oven unless the countertop is at least 40 mm thick.

  • Page 25

    Safety instructions for installation Upper clearance If there are several appliances beneath the exhaust hood, e.g., a wok burner and an electric cooktop, and there are different clearance distances listed in the Operating and installation instructions, always choose the greatest distance. For an exhaust hood above the appliance, always follow the safe clearance distance indicated by the...

  • Page 26

    2" 2" (50mm) CS 1112 (50mm) CS 1122 CS 1212 CS 1212-1 CS 1221 CS 1223 CS 1326 not recommended CS 1327 6" (150 mm) CS 1322 CS 1421 10" (250 mm) CS 1012...

  • Page 27

    Safety instructions for installation Minimum distance underneath Shelf To ensure proper ventilation of the Installation of an intermediate shelf appliance, a minimum distance below under the cooktop is not required but the appliance to an oven, intermediate allowed. shelf or drawer is required. For the positioning of the power cord a The minimum distance from the bottom gap of 10 mm is required at the rear.

  • Page 28: Installation

    Installation Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2"...

  • Page 29: Installation Dimensions

    Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply cable (encased in flexible metal conduit), L = 78 " (2000 mm) e Data plate...

  • Page 30: Cut Out

    Installation Cut out If during installation the seal around ^ Make the worktop cut-out for one or the frame does not sit flush with the more appliances as applicable. countertop in the corners, the corner Remember to maintain a minimum radius, maximum "...

  • Page 31: Installation Of Multiple Appliances

    Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out Countertop cut-out two appliances three appliances For the installation of two appliances For the installation of three appliances the width of the countertop cut-out D is the width of the countertop cut-out D is the sum of A and C.

  • Page 32

    Installation Sample calculations for a countertop cut-out for three appliances appliance width appliance width appliance width Countertop minus " (8 mm) minus " (8 mm) cut-out 11" " 11" " (280 mm) (280 mm) (848 mm) (288 mm) 11" 15" "...

  • Page 33

    Installation a Spring clips b Support bars c Space between support bar and countertop d Cover strip The illustration represents the attachment of spring clips a and support bars b for 3 appliances. An additional support bar is required for each additional appliance. The position for attachment of an additional support bar depends on the width of the appliance B (288 mm / 380 mm / 576 mm).

  • Page 34: Attaching The Spring Clips And Support Bars

    Attaching the spring clips and support bars Wood countertop ^ Place the supplied spring clips a and the support bars b at the marked positions on the upper edge of the cut-out. ^ Use the supplied 3.5 x 25 mm screws to attach the spring clips and support bars.

  • Page 35

    Attaching the spring clips and support bars Granite countertop Screws are not needed for stone countertops. ^ Coat the side and bottom edges of the spring clips a and support bars b with silicone. ^ Fill the space e between the support ^ Position and attach the spring clips bars and the countertop with silicone.

  • Page 36: Installing The Appliance(s)

    Installing the appliance(s) ^ Feed the appliance connection cable ^ Place the front edge of the next down through the worktop cut-out. appliance into the countertop cut-out. ^ Place the front edge of the appliance ^ Connect the appliance(s) to the into the countertop cut-out.

  • Page 37: General Installation Tips

    General installation tips Seal between appliance and Tiled surfaces countertop The grouting a and the shaded area The sealing strip under the edge of the top part of the appliance provides an below the appliance frame must be adequate seal with the countertop. smooth and flat, so that the frame will lie evenly and the sealing strip under The appliance must not be sealed...

  • Page 38: Electrical Connection

    Electrical connection Power supply CAUTION: Before installation or ^ Make sure your electrical supply servicing, disconnect the power matches the data plate. supply by either removing the fuse, shutting off the main power supply The combiset is equipped with a or manually "tripping"...

  • Page 39: Help Protect Our Environment

    Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling authority about the possibility of recycling these materials.

  • Page 40

    Alteration rights reserved / 4511 M.-Nr. 07 353 931 / 01 For the most updated manual, please visit the Miele web site.

Comments to this Manuals

Symbols: 0
Latest comments: