Download Print this page

Advertisement

Operating and installation instructions
Induction wok
CS 1223
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 07 180 670

Advertisement

   Summary of Contents for Miele CS 1223

  • Page 1

    Operating and installation instructions Induction wok CS 1223 en - GB To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 180 670...

  • Page 2: Table Of Contents

    Contents Guide to the appliance ..........4 Warning and Safety instructions .

  • Page 3

    Contents Safety instructions for installation ........27 Appliance and building-in dimensions .

  • Page 4: Guide To The Appliance

    Guide to the appliance a Wok basin (C 300 mm) e Display rating: 2400 W ß No wok on cooking zone, with Booster: 3200 W or wok unsuitable b Wok Auto heat-up c Control knob Fault d Indicators (see "Problem solving guide") C / 0 Safety switch off Indicators...

  • Page 5

    Guide to the appliance Accessories supplied The wok supplied with your CombiSet appliance as well as a range of optional accessories are available to order (see "Optional accessories").

  • Page 6: Warning And Safety Instructions

    Warning and Safety instructions Correct application This appliance is built in accordance This appliance is intended for with current safety requirements. domestic use only and must be used as Improper use of the appliance can, described in these instructions. however, present a risk of both Any other usage is at the owner's risk personal injury and material and could be dangerous.

  • Page 7

    Warning and Safety instructions Safety with children Take care that children are not able to pull the wok down off the appliance. Activate the safety lock to ensure Turn the wok handle inwards away from that children cannot switch on the the edge of the appliance.

  • Page 8

    The manufacturer cannot be qualified electrician with a special held liable for the consequences of an connection cable of type H 05 V V-F inadequate earthing system (e.g. (pvc insulated), available from the Miele electric shock). Service Department.

  • Page 9

    Warning and Safety instructions Never open the casing. Tampering Faulty components must only be with electrical connections or replaced by genuine Miele original components and mechanical parts is spare parts. The manufacturer can only highly dangerous to the user and can guarantee the safety of the appliance cause operational faults.

  • Page 10

    Warning and Safety instructions Correct use Do not cover the appliance, e.g. with a cloth, kitchen foil, etc. This could For people fitted with a heart be a fire hazard if the appliance is pacemaker: switched on by mistake. Please note that the area immediately surrounding the appliance is Do not leave the appliance electromagnetically charged, and that...

  • Page 11

    Warning and Safety instructions Keep the appliance clean. Grains of Do not use the appliance as a salt, sugar and sand (e.g. from resting place for anything else. Take cleaning vegetables) can cause particular care never to place cutlery or scratches.

  • Page 12: Caring For The Environment

    Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment.

  • Page 13: Before Using For The First Time

    Before using for the first time Before using for the first time Please stick the extra data plate for the appliance supplied with this When the induction wok is first documentation in the space provided in connected, and after a power cut, all of the "After sales service"...

  • Page 14: Induction

    Induction The induction principle Take particular care never to place An induction coil is located underneath cutlery or other metal objects on the the induction wok. When the appliance appliance. When the appliance is is switched on, this coil creates a switched on either deliberately or by magnetic field.

  • Page 15: Suitable Pans

    Induction Suitable pans Noises The following noises might occur when Only use the wok supplied with the the induction wok is in operation: appliance for cooking food. This wok is designed specifically for the – On the higher power settings, it appliance.

  • Page 16: Operation

    Operation Switching on and off Residual heat indicator The induction wok is switched on by The residual heat indicator remains on turning the control clockwise a to the until the induction wok is cool enough power setting required, and is switched to touch.

  • Page 17: Settings

    Operation Settings When Auto heat-up has been activated, the induction wok switches on Cooking process Settings automatically at the highest setting and then switches to the continued cooking Keeping food warm, 1 - 2 setting selected. The heat-up time melting chocolate depends on which continued cooking Warming food up 3 - 6...

  • Page 18: Booster Function

    Operation Booster function To switch on the booster function ^ Turn the control past power setting 9 The induction wok is equipped with a booster function which increases the to BI, and then back to 9. power level. I appears in the display, and the B If activated, the appliance will operate indicator also lights up.

  • Page 19: Safety Features

    Safety features Lock To deactivate the system lock ^ Turn the control anticlockwise as far The induction wok is fitted with a safety lock to prevent unauthorised use, e.g. as it will go, and hold in that position until the L goes out, and 0 appears by children.

  • Page 20: Safety Switch-off

    Safety features Safety switch-off Power setting Maximum The induction wok is fitted with a safety operating time in switch-off feature in case you forget to hours switch it off yourself. If the induction hob is heated for an unusually long period of time (see chart), and the power setting is not altered, it will switch itself off automatically.

  • Page 21: Overheating Protection

    Safety features Overheating protection The induction coil can overheat if The induction coil is equipped with – the appliance is used for too long at overheating protection. Before the maximum power. induction coil gets too hot, overheating – the appliance is not well enough protection cuts in in one of the following ventilated.

  • Page 22: Cleaning And Care

    Cleaning and care Miele offer a range of branded cleaning To avoid damaging the surface of and conditioning products. See your appliance, do not use: "Optional accessories". – cleaning agents containing soda, alaklines, ammonia, acids or Under no circumstances use a...

  • Page 23: Ceramic Surface

    Cleaning and care Ceramic surface Stainless steel Remove light soiling with a damp cloth. The ceramic and stainless steel hob cleaner can be used to clean the frame Then clean the appliance with a when required (see "Optional suitable ceramic and stainless steel accessories").

  • Page 24: Problem Solving Guide

    Check whether the control is damaged dangerous. The manufacturer or stuck. cannot be held liable for If this is not the case, call the Miele unauthorised work. Service Dept. What to do if..F and a number flash alternately in the display.

  • Page 25

    Problem solving guide ... one of the following has occurred: ... The cooling fan continues to run after the appliance has been – The booster has automatically switched off switched off early. This is not a fault. The fan will continue –...

  • Page 26: Optional Accessories

    These can be ordered via the internet at www.miele-shop.com or from the Miele Customer Service Department (see back cover) or from your Miele dealer. Wok lid Other accessories Ceramic and stainless steel hob cleaner 250 ml...

  • Page 27: Safety Instructions For Installation

    Safety instructions for installation This appliance must not be installed Fit the wall units and extractor hood over a dishwasher, washing machine, before fitting the appliance to avoid tumble dryer, refrigerator or freezer. damaging the surface. The high temperatures radiated by hobs could damage the appliance The veneer or laminate coatings of below.

  • Page 28

    Safety instructions for installation Safety distance above the appliance When two or more appliances are installed together below a cooker hood, e.g. an induction hob or wok and a gas hob combiset, which have different safety distances given in the installation instructions, you should select the greater distance of the two.

  • Page 29

    The minimum distance a between the worktop cut-out and a wall or tall unit to the right or left of it is: 40 mm CS 1212 CS 1221 CS 1234 CS 1223 50 mm CS 1112 CS 1122 Not recommended CS 1134 CS 1326...

  • Page 30

    Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding There must be a minimum distance of 50 mm between the niche cladding and the worktop cut-out. This distance is only necessary for niche cladding made of wood or any other combustible material.

  • Page 31: Appliance And Building-in Dimensions

    Appliance and building-in dimensions CS 1223 1 0 8 5 2 0 3 8 0 3 6 4 ß R 4 5 0 0 1 9 8 a Spring clamps b Front c Building-in depth d Mains connection cable, L = 2,000 mm...

  • Page 32: Preparing The Worktop

    Preparing the worktop ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance.

  • Page 33: Installation Of Several Appliances

    Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fitting the spacer bars and support brackets". Worktop cut-out Worktop cut-out - two appliances - three appliances To calculate the cut-out width required: Add up the widths of each appliance and subtract 16 mm from this figure (i.

  • Page 34

    Installation of several appliances Positioning the spacer bars and spring clamps 2 5 - 3 0 5 0 5 0 2 5 - 3 0 5 6 8 3 7 2 / 2 8 0 / 5 7 6 3 8 0 / 2 8 8 / 5 6 8 3 7 2 /...

  • Page 35: Fixing The Spring Clamps And Spacer Bars

    Fixing the spring clamps and spacer bars Wooden worktops Granite and marble worktops The screws are not required for 2 5 - 3 0 granite or marble worktops. 2 5 - 3 0 ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions ^ Position and secure the spring marked.

  • Page 36

    Fixing the spring clamps and spacer bars ^ Coat the side edges and the lower edges of the spring clamps with silicone. ^ Then fill gap d between the spacer bars and the worktop with silicone from the tube supplied.

  • Page 37: Installing The Appliance

    Installing the appliance Installing the appliance ^ Feed the connection cable down through the cut-out. ^ Then drop the front edge of the appliance into the cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position.

  • Page 38: General Installation Tips

    General installation tips Do not use sealant between the frame of the top part of the appliance and the worktop. This could cause difficulties if it ever needs to be taken out for servicing and possibly result in damage to the frame or the worktop.

  • Page 39: Electrical Connection

    H 05 V V-F be provided for all poles. (pvc insulated), available from Miele. For extra safety it is advisable to install a suitable residual current device Installation, repairs and other work (RCD).

  • Page 40

    Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. It is most important that this basic safety requirement is present and tested regularly and if there is any doubt the electrical wiring in the home should be inspected by a...

  • Page 41: After Sales Service, Data Plate

    Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. Space in which to stick the extra data plate supplied with the appliance. Ensure...

  • Page 44

    Alteration rights reserved/ 2808 M.-Nr. 07 180 670 / 01...

Comments to this Manuals

Symbols: 0
Latest comments: