Subscribe to Our Youtube Channel
Related Manuals for Winco ULPSS15B2W
Summary of Contents for Winco ULPSS15B2W
- Page 1 PACKAGED STANDBY SYSTEM INSTALLATION AND OPERATORS MANUAL ULPSS15B2W/E 088-00 60706-207...
-
Page 2: Table Of Contents
The warranty listed in the manual describes the number and other vital information here. If you what you can expect from WINCO should you need should ever need to contact us on this unit it will help service assistance in the future. -
Page 3: Safety Information
SAFETY INFORMATION 2. FIRE HAZARD Natural gas and L.P. present a hazard of possible explosion and/or fire. This engine generator set has been designed and a. Keep fuel containers out of reach of children. manufactured to allow safe, reliable performance. b. -
Page 4: Description
LINE SIDE GENERATOR The package standby system is designed to au- CONTACTOR SIDE CONTACTOR tomatically provide standby power to unattended ULPSS15B2W 00 AMPS 00 AMPS loads during electrical outages. Upon interruption 200 AMPS 200 AMPS of normal electrical service, the packaged standby... -
Page 5: Specifications
SPECIFICATIONS “Concealed Damage” is understood to mean dam- age to the contents of a package which is not evident at the time of delivery by the carrier, but GENERATOR which is discovered later. The carrier or carriers are responsible for merchandise lost or damaged in tran- MODEL WATTS* VOLTS... -
Page 6: Fuel Installation
ENGINE GENERATOR SET MOUNTING These fuel pressures are critical; failure to provide the proper pressure can cause many problems rang- WARNING - Personal Injury ing from a unit that will not start to causing damage to the fuel system. The enclosures on these units can become very hot adjacent to the exhaust areas. -
Page 7: Fuel Installation
FUEL PRESSURE FEET SIZE OF PIPE LP & NG VAPOR FUEL Correct fuel pressure can- up to 25 FT* 3/4 “ Pipe not be stressed enough. The most common cause 25 - 100 FT* 1” Pipe for inoperative systems is an inadequate or incor- over 100 FT* Use a two regulator rect fuel pressure. -
Page 8: Fuel Conversions
LP TANK SIZING Shown below is a diagram of a natural gas (NG) installation. Required LP tank size for LP Vapor withdrawal operating at various outside temperatures given in degrees Fahrenheit (Celsius). TANK TEMPERATURE TANK SIZE 60° F (16° C) 150 GALLON 32°... -
Page 9: Battery Installation
MINIMUM the evidence of reaction, foaming, has ceased. CCA Rating The resulting liquid is to be flushed with water ULPSS15B2W and the area dried. Installation and servicing of batteries must be DANGER - Explosive Fire Risk performed or supervised only by personnel knowl- edgeable of batteries and the required precautions. - Page 10 088-00 60706-207...
- Page 11 MOUNTING THE AUTOMATIC **** CAUTION **** TRANSFER SWITCH (ATS) EQUIPMENT DAMAGE - Always connect the posi- tive cable first and the negative cable last. When ****************** disconnecting, remove the negative cable first and ***** WARNING ***** the positive cable last. Failure to connect and dis- ****************** connect in the proper sequence can cause equip- EQUIPMENT DAMAGE - Protect the switch from...
- Page 12 This will allow you to test the generator under load. Should you ever have to work on the switch, you will WINCO UL ATS (ASCO 185) be able to disconnect the power and work on the switch cold without having the power company pull See the ASCO installation manual for additional your meter.
- Page 13 DC ELECTRICAL INITIAL START UP INTERCONNECTION ****************** ***** WARNING ***** **** CAUTION **** ****************** DO NOT jump start these engine generator sets. Never run the AC and DC wiring in the same con- Starting these units on a low battery of jump start- duit.
- Page 14 DSE 3110 CONTROL STOP/RESET (Red Button) This button places the module into its “Stop/ Reset” mode. This will clear any alarm conditions for which the triggering criteria have been removed. The fuel supply de-energizes and the engine comes to a standstill. Should a remote start signal be present while operating in this mode, a remote start WILL NOT occur.
- Page 15 START UP PROCEDURE With the engine running smoothly, check the no load Engine Generator Set only voltage and frequency at wire # and # 4 (L2 and L6 in the ASCO ATS) on the generator terminal block The engine control module (ECM) is manufactured in the ATS.
-
Page 16: Indicator Lights
Transfer Switch & Engine Generator DESCRIPTION The digital controller provides sensing, timing, and Automatic (remote) Operation control functions for the ATS. This micro-processor- This procedure checks the electrical operation of based controller includes built-in control buttons and the automatic transfer switch. If the actual operation status lights for control of the ATS and the generator. - Page 17 The transfer switch can be set up to exercise the generator with or without a load transfer. Normally Winco generators exercise without a load transfer. This is because you may not wish to have a mo- mentary interruption of power. Turn the exerciser dipswitch on.
- Page 18 088-00 60706-207...
- Page 19 FRONT PANEL CONFIGURATION This configuration mode allows the operator limited customizing of the way the module operates. Use the module’s navigation buttons to traverse the menu and make value changes to the parameters. . ACCEPT button. . ACCEPT button. 2. NEXT PAGE button. 2.
-
Page 20: Fault Codes
DSE 3110 CONTROL FAULT CODES DESCRIPTION Auxiliary inputs can be user configured and will display AUXILIARY INPUTS the message as written by the user. The engine has not fired after the preset number of start FAIL TO START attempts The module has detected a condition that indicates that the engine is running when it has been instructed to stop. -
Page 21: Preventive Maintenance
PREVENTIVE DSE 3110 ENGINE CONTROL MAINTENANCE PROTECTIONS When an alarm is present, the Common alarm LED Reasonable care in preventive maintenance will if configured will illuminate. The LCD display will insure high reliability and a long life for the engine show an icon to indicate the failure. - Page 22 ENGINE GENERATOR SET LAYOUT ULPSS15B2W/E 088-00 60706-207...
- Page 23 088-00 60706-207...
- Page 24 TROUBLESHOOTING ENGINE CRANKS BUT WILL NOT START TABLES . Improper fuel pressure being delivered to unit. 2. Fuel supply shut off. 3. Fuel supply empty. ******************** 4. Defective spark plug. ****** WARNING ****** 5. Defective engine ignition module. ******************** 6. Dirty air cleaner filter. 7.
- Page 25 088-00 60706-207...
-
Page 26: Maintenance Log
MAINTENANCE LOG DATE ITEM WORK PERFORMED HOURS 088-00 60706-207... - Page 27 MAINTENANCE LOG DATE ITEM WORK PERFORMED HOURS 088-00 60706-207...
-
Page 28: Month Limited Warranty
WINCO’s sole liability, and Purchaser’s sole remedy for a failure under this warranty, shall be limited to the repair of the product. At WINCO’s option, material found to be de- fective in material or workmanship under normal use and service will be repaired or re- placed.
Need help?
Do you have a question about the ULPSS15B2W and is the answer not in the manual?
Questions and answers