Related Manuals for Winco ULPSS12H2W
Summary of Contents for Winco ULPSS12H2W
- Page 1 PACKAGED STANDBY SYSTEM INSTALLATION AND OPERATORS MANUAL ULPSS12H2W/E 075-0 60706-209...
-
Page 2: Table Of Contents
If you c. Never operate the unit in such a way as to what you can expect from WINCO should you need should ever need to contact us on this unit it will help... -
Page 3: Description
LINE SIDE GENERATOR ****************** ENGINE SPECIFICATIONS CONTACTOR SIDE CONTACTOR The package standby system includes all times ULPSS12H2W 00 AMPS 00 AMPS Before proceeding with the installation be sure the necessary for a completely automatic standby power 200 AMPS 200 AMPS Refer to engine operating and maintenance instruc- operation selector switch is in the stop position. -
Page 4: Fuel Installation
ENGINE GENERATOR SET MOUNTING These fuel pressures are critical; failure to provide A low pressure regulator is installed to further reduce ****************** the proper pressure can cause many problems rang- the fuel pressure to the required four (4) to six (6) oz. ***** WARNING ***** WARNING - Personal Injury ing from a unit that will not start to causing damage... -
Page 5: Fuel Installation
CCA Rating soda (baking soda) to one gallon of water. The **** CAUTION **** ULPSS12H2W bicarbonate of soda solution is to be added until the evidence of reaction, foaming, has ceased. EQUIPMENT DAMAGE - NEVER JUMP START... -
Page 6: Battery Installation
AC ELECTRICAL CONNECTING THE BATTERY CHARGER CONNECTIONS A two-stage battery tender is provided on all PSS series generators. This battery tender charges at a rate of 750 mA until the battery is fully charged NOTICE - CLASS 1 WIRING METHODS ARE TO and then automatically switches to a .2 VDC float BE USED FOR ALL FIELD WIRING CONNEC- charger. -
Page 7: Initial Start Up
Deep Sea Electronics. Model 0 is used on Battery Negative White WINCO UL ATS (ASCO 165) ATS panel as the ATS is not service enterance rated. this engine generator set. See picture below. Ad- This will alow you to test the generator under load. - Page 8 DSE 3110 ENGINE CONTROL . Turn on the preferred source (utility) circuit Transfer Switch does not transfer the load to the In order to set and test the exercise circuit the breaker. The utility source acceptable light should generator set. The Transfer Switch on utility (pre- engine control module must be set in the auto now come on as well as the transfer switch on utility ferred source) light stays on.
- Page 9 FRONT PANEL CONFIGURATION DSE 3110 CONTROL This configuration mode allows the operator limited customizing of the way the module operates. Use the module’s navigation buttons to traverse the menu and make value changes to the parameters. . ACCEPT button. . ACCEPT button. 2.
-
Page 10: Fault Codes
PREVENTIVE MAINTENANCE LOG DSE 3110 CONTROL MAINTENANCE FAULT CODES DATE WORK PERFORMED Reasonable care in preventive maintenance will insure high reliability and a long life for the engine generator set and Automatic Transfer Switch. DESCRIPTION ***************** Auxiliary inputs can be user configured and will display ***** WARNING ***** AUXILIARY INPUTS the message as written by the user. - Page 11 ENGINE GENERATOR SET LAYOUT ULPSS12H2W/E 075-0 60706-209 075-0 60706-209...
-
Page 12: Troubleshooting Tables
TROUBLESHOOTING ENGINE CRANKS BUT WILL NOT START TABLES . Improper fuel pressure being delivered to unit. 2. Fuel supply shut off. . Fuel supply empty. ******************** 4. Defective spark plug. ****** WARNING ****** 5. Defective engine ignition module. ******************** 6. Dirty air cleaner filter. 7. -
Page 13: Month Limited Warranty
WINCO’s sole liability, and Purchaser’s sole remedy for a failure under this warranty, shall be limited to the repair of the product. At WINCO’s option, material found to be de- fective in material or workmanship under normal use and service will be repaired or re- placed.
Need help?
Do you have a question about the ULPSS12H2W and is the answer not in the manual?
Questions and answers