Download  Print this page
   

Advertisement

www.ergotron.com
User's Guide - English
Guía del usuario - Español
Manuel de l'utilisateur - Français
Gebruikersgids - Nederlands
Benutzerhandbuch - Deutsch
Guida per l'utente - Italiano
Användarhandbok - svenska
ユーザーガイ ド : 日本語
用户指南 : 汉语
0.78"-2.56" (20-65mm)
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
888-45-300-G-00 rev. C • 11/13
5-15 lbs
(2.27-6.8 kg)
Important!
You will need to adjust this product after installation is complete.
Make sure all your equipment is properly installed on the
product before attempting adjustments. This product should
move smoothly and easily through the full range of motion and
stay where you set it. If movements are too easy or diffi cult or if
product does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements. Depending
on your product and the adjustment, it may take many turns to
0.5"-2.5"
notice a diff erence. Any time equipment is added or removed from
(13-64mm)
this product, resulting in a change in the weight of the mounted
load, you should repeat these adjustment steps to ensure safe and
optimum operation.
WorkFit-P
Reduce.Reuse.Recycle
1 of 8

Advertisement

Table of Contents

   Also See for Ergotron WorkFit-P

   Related Manuals for Ergotron WorkFit-P

   Summary of Contents for Ergotron WorkFit-P

  • Page 1 WorkFit-P www.ergotron.com User's Guide - English Guía del usuario - Español Manuel de l’utilisateur - Français Gebruikersgids - Nederlands Benutzerhandbuch - Deutsch Guida per l’utente - Italiano Användarhandbok - svenska ユーザーガイ ド : 日本語 用户指南 : 汉语 5-15 lbs (2.27-6.8 kg) Important! You will need to adjust this product after installation is complete.
  • Page 2: Hazard Symbols Review

    Hazard Symbols Review Symbol Signal Word Level of Hazard These symbols alert users of a safety condition that A NOTE indicates important information that helps you demands attention. All users should be able to NOTE make better use of this product. recognize and understand the signifi cance of the fol- lowing Safety Hazards if encountered on the product A CAUTION indicates either potential damage to...
  • Page 3: Tools Needed

    Features 20” 360˚ 180˚ Components M4 x 14mm M4 x 8mm 1x 1x 4 mm 2.5 mm Tools Needed 13mm 888-45-300-G-00 rev. C • 11/13 3 of 8...
  • Page 4: Setup Steps

    Set-up Steps Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and equipment. CLAMP GROMMET 4 mm DESK THICKNESS 4 mm 0.78"-1.38" (20-35mm) 1.18"-2.56" (30-65mm) 4 mm CAUTION: Bolt must be centered in hole.
  • Page 5 Set-up Steps 2.5 mm M4 x 14mm M4 x 8mm 1x 1x 4 mm 888-45-300-G-00 rev. C • 11/13 5 of 8...
  • Page 6 Adjustment Step Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
  • Page 7 Adjustment Step Increase Friction If this product moves too easily from side-to-side, then you'll need to increase friction: Decrease Friction If this product is too diffi cult to move from side-to-side, then you'll need to decrease friction: 13mm 888-45-300-G-00 rev. C • 11/13 7 of 8...
  • Page 8 Set Your Workstation to Work For YOU! Confi gure su estación de trabajo para que trabaje para USTED. Ajustez votre station de travail en fonction de VOS besoins ! Richten Sie Ihren Arbeitsplatz so ein, dass er für SIE arbeitet! Stel uw werkstation zo in dat het voor U werkt! Approntare la stazione di lavoro nella posizione ergonomica ottimale.

Comments to this Manuals

Symbols: 0
Latest comments: