Rugged industrial panel pc with intel pentiumæ 4 or celeron and 15" lcd display (114 pages)
Summary of Contents for Advantech IDK-1105 Series
Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 3
Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
Page 4
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
This specification applies to the 5.7” inch color TFT LCD module IDK-1105R. IDK-1105R is designed to operate in a wide range of operating temperatures and has long life LED backlights that are well-suited to display units for industrial applications. An LED driving board for backlight unit is included in this panel and the structure of the LED unit is replaceable.
Page 9
[degree] Horizontal Point - 5 CR 10 Viewing Angle 1,4,6 [degree] Vertical Point - 5 CR 10 Red x 0.566 0.616 0.666 Red y 0.302 0.352 0.402 Green x 0.308 0.358 0.408 Green y 0.518 0.568 0.618 Color/Chromaticity Coor- dinates (CIE 1931) Blue x 0.096 0.146...
Page 10
Note 5: Definition of Luminance Uniformity Measure Maximum luminance [L(MAX)] and Minimum luminance [L(MIN)] on 9 points Luminance Uniformity is calculated with the following formula: L = [ L(MIN) / L (MAX) ] X 100% Note 6: Definition of Viewing Angle IDK-1105 User Manual...
TFT LCD Module 2.1.1 Power Specifications Table 2.1: Power Specifications Item Symbol Values Unit Remarks Min. Typ. Max. Power Voltage For LCD Power Voltage For Backlight = 5V LCD Power Current Note 1 LED Backlight Power Current Logic Input Input Voltage -0.5 +0.5 V Voltage...
Table 2.2: Signal Electrical Characteristics Differential Input Leakage RVxliz Current Backlight Unit 2.2.1 Parameter Guidelines for LED backlight Following characteristics are measured under a stable condition using an inverter at 25°C (Room Temperature): Table 2.3: For IDK-1105 Item Symbol Values Unit Remark Min.
Signal Description LVDS is a differential signal technology for LCD interface and high speed data trans- fer device. The connector pin definition is as below. Note: “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for “Not Connected.” 3.1.1 Signal Description J2 LVDS connector: CSTAR CP100-S20G-H16 Table 3.1: Symbol Description...
Note: 1. PWM adjusts brightness to control Pin, Pulse duty the bigger the brighter. 2. PWM signal = 0 ~ 5.0V, operation frequency: 100Hz~200 KHz Interface Timing 3.2.1 Timing Characteristics DE mode only Table 3.2: Timing Characteristics Values Parameter Symbol Unit Min.
Touch Characteristics This touch panel is a resistance type that customers use with flat displays like LCDs. Once an operator touches it, the circuit sends coordinate points to the PC from the voltage at contact points. Item Specification Remarks Operating tempera- -20°C ~ 70°C ture Storage temperature...
Touch Controller Characteristics Advantech ETM-RES05C touch control board is the ultimate combo board. This touch panel controller provides optimum performance of your analog resistive touch panels for 4-wire models. It communicates with the PC system directly through USB and RS-232 connector. You can see how superior the design is in sensitivity accu- racy and friendly operation.
Figure 5.1 Board mounted header 5.4.3 Touchscreen Connector, JP2, Pins and Signal Descriptions The Touchscreen connector, JP2, is a FFC/FPC SMD 1.0 mm 4-pin 90° degree, female type connector. The pins are numbered as shown in the table below. TS4 Pin # Signal Name Signal Description Bottom...
Page 30
Handling Precautions The optical characteristics are measured under stable conditions at 25°C (Room Temperature) Since front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input con- nector.