Sharp MX-1810U Service Manual page 187

7-6
Purpose Setting
Function (Purpose) Used to set the operating intermittent aging
cycle.
Section
Operation/Procedure
1) Enter the intermittent aging operation cycle (unit: sec) with 10-
key.
2) Press [OK] key.
The time entered in procedure 1) is set.
* The interval time that can be set is 1 to 900 (sec).
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
7-8
Purpose Operation display
Function (Purpose) Used to display the warm-up time.
Section
Operation/Procedure
Press [EXECUTE] key.
Counting of the warm-up time is started and the time required for
warm-up is displayed
* Interruption of counting by pressing [EXECUTE] key is inhibited.
7-9
Purpose Operation test/check
Function (Purpose) Color setting in the color copy test mode
(Used to check the copy operation and the
image quality for each color).
Section
Operation/Procedure
1) Select the copy color with the touch panel key.
(Two or more colors can be selected.)
The key of the selected color is highlighted.
2) Press [EXECUTE] key.
Copying is performed with the selected color.
When [CLOSE] key is pressed, the display goes into the copy oper-
ation menu in the simulation mode.
K Setup/cancel of black
C Setup/cancel of cyan
M Setup/cancel of magenta
Y Setup/cancel of yellow
7-12
Purpose Operation test/check
Function (Purpose) The document reading number of sheets
setting (for aging operation)
Section RSPF
Operation/Procedure
1) Set document reading quantity with 10-key.
(Setting range:0 - 255)
2) Press [OK] key. The set value is saved.
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
8
8-1
Purpose
Function (Purpose) Used to check and adjust the operations of
Section
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] keys on the touch
panel.
2) Select a target item to be adjusted with scroll keys.
3) Enter the setting value with 10-key. (The value specified on the
label of the high voltage PWB must be entered.)
* When the
item can be changed with 1up (1down) collectively.
4) Press [EXECUTE] key.
The set value is saved and the voltage entered with step 3) is
output for 30 sec.
When [EXECUTE] key is pressed, the output is terminated.
Item/Display (Mode)
MIDDLE
LOW
MX-3610N SIMULATION 5 – 18
Operation test/check/adjustment
the developing voltage in each print mode
and the control circuit.
* When the middle speed is adjusted, the
low speed are also adjusted simulta-
neously.
Process (Developing)
key is pressed, the setting value of each
Content
A MIDDLE Developing K
SPEED bias voltage
DVB_K (Middle
speed mode)
B MIDDLE Developing C
SPEED bias voltage
DVB_C (Middle
speed mode)
C MIDDLE Developing M
SPEED bias voltage
DVB_M (Middle
speed mode)
D MIDDLE Developing Y
SPEED bias voltage
DVB_Y (Middle
speed mode)
A LOW Developing K
SPEED bias voltage
DVB_K (Low speed
mode)
B LOW Developing C
SPEED bias voltage
DVB_C (Low speed
mode)
C LOW Developing M
SPEED bias voltage
DVB_M (Low speed
mode)
D LOW Developing Y
SPEED bias voltage
DVB_Y (Low speed
mode)
Adjustment Actual
range voltage
0 - 600 –450V
5V
0 - 600 –450V
5V
0 - 600 –450V
5V
0 - 600 –450V
5V
0 - 600 –450V
5V
0 - 600 –430V
5V
0 - 600 –430V
5V
0 - 600 –430V
5V