Sharp MX-1810U Service Manual page 168

Item/Display Content
C FRONT Alignment position
ADJUST adjustment (front)
D REAR Alignment position
ADJUST adjustment (Rear)
E STAPLE REAR Stapling position
adjustment (Rear,
one position)
F STAPLE REAR Stapling position
R adjustment (Rear,
one position /R
series)
G STAPLE Stapling position
FRONT adjustment (one
position in front)
H STAPLE Stapling position
FRONT R adjustment (Front,
one position / R
series)
I STAPLE BOTH Stapling position
adjustment (Two
positions, center)
J STAPLE Stapling position
PITCH adjustment (Two
positions, pitch)
K PUNCH Punch center
CENTER adjustment
Purpose
Setting Default (Case where the
range value adjustment is
required)
35 - 65 50 When the paper
alignment capability
in the stacker
section is improper,
the paper alignment
width is adjusted.
35 - 65 50
25 - 75 50 When the stapling
position on the R
side is shifted, the
adjustment is
executed.
45 - 75 50 When the stapling
position on the R
side is shifted with R
series paper, the
adjustment is
executed.
25 - 75 50 When the stapling
position on the F
side is shifted, the
adjustment is
executed.
25 - 55 50 When the stapling
position on the F
side is shifted with R
series paper, the
adjustment is
executed.
45 - 55 50 When the staple off-
center is shifted, the
adjustment is
executed.
35 - 62 50 When the stapling
interval is to be
changed, the
adjustment is
executed.
35 - 65 50 When the punch off-
center is shifted, the
adjustment is
executed.
MX-3610N ADJUSTMENTS AND SETTINGS 4 – 92
Change when the adjustment value is increased
or decreased
F side paper When the adjustment value is
alignment plate stop increased, the alignment
position position is shifted to the
(F/R direction) center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
R side paper When the adjustment value is
alignment plate stop increased, the alignment
position position is shifted to the
(F/R direction) center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
Stapling position When the adjustment value is
(stapler stop increased, the distance
position) between the stapling position
(F/R direction) and the paper edge becomes
longer.
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
Stapling position When the adjustment value is
(stapler stop increased, the distance
position) between the stapling position
(F/R direction) and the paper edge becomes
longer.
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
Stapling position When the adjustment value is
(stapler stop decreased, the distance
position) between the stapling position
(F/R direction) and the paper edge becomes
shorter.
When the adjustment value is
increased, the distance
between the stapling position
and the paper edge becomes
longer.
Stapling position When the adjustment value is
(stapler stop decreased, the distance
position) between the stapling position
(F/R direction) and the paper edge becomes
shorter.
When the adjustment value is
increased, the distance
between the stapling position
and the paper edge becomes
longer.
Stapling position When the adjustment value is
(stapler stop increased, the stapling
position) position is shifted to the front.
(F/R direction) When the adjustment value is
decreased, the stapling
position is shifted to the rear.
Stapling position When the adjustment value is
(stapler stop increased, the pitch of two
position) points is widened.
(F/R direction) When the adjustment value is
decreased, the pitch of two
points is narrowed.
Punching position When the adjustment value is
(F/R direction) increased, the hole position is
shifted to the front.
When the adjustment value is
decreased, the hole position
is shifted to the rear.
Change when
the adjustment
value is
changed by 1
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm