Sharp MX-1810U Service Manual page 182

Item/Display Content
E STAPLE Stapling position
BOTH adjustment (center
position of two
positions binding)
F STAPLE Stapling position
PITCH adjustment (staple
pitch of two
positions binding)
G PUNCH Punch center
CENTER positioning sensor
H PUNCH Punch hole
HOLE adjustment (paper
transport direction)
Saddle stitch finisher (MX-FN10)
Item/Display Content
A SADDLE Saddle stitch
POSITION position
adjustment
B FOLDING Saddle folding
POSITION position
adjustment
C FRONT Alignment position
ADJUST adjustment (front)
D REAR Alignment position
ADJUST adjustment (Rear)
E STAPLE REAR Stapling position
adjustment (Rear,
one position)
Setting Default Purpose (Case where the
range value adjustment is required)
68 - 132 100 When the staple off-center is
shifted, perform the
adjustment.
68 - 132 100 When it is required to change
the staple interval, perform
the adjustment.
37 - 63 50 When the punch off-center is
shifted, perform the
adjustment.
42 - 58 50 When the punch hole position
is shifted in the transport
direction, perform the
adjustment.
Purpose
Setting Default (Case where the
range value adjustment is
required)
25 - 75 50 The adjustment is
executed when the
saddle staple
position is shifted.
25 - 75 50 The adjustment is
executed when the
saddle folding
position is shifted.
35 - 65 50 When the paper
alignment capability
in the stacker
section is improper,
the paper alignment
width is adjusted.
35 - 65 50
25 - 75 50 When the stapling
position on the R
side is shifted, the
adjustment is
executed.
MX-3610N SIMULATION 5 – 13
Change when the adjustment value is
increased or decreased
Staple When the adjustment value is
position increased, the staple position is
(Stapler stop shifted to the rear side.
position) When the adjustment value is
(F/R decreased, the staple position is
direction) shifted to the front side.
Staple When the adjustment value is
position increased, the staple interval is
(Stapler stop increased.
position) When the adjustment value is
(F/R decreased, the staple interval is
direction) decreased.
Punch When the adjustment value is
position decreased, the punch position is
(F/R shifted to the front side.
direction) When the adjustment value is
increased, the punch position is
shifted to the rear side.
Punch When the adjustment value is
position increased, the punch position is
(Paper shifted to the paper lead edge side.
transport When the adjustment value is
direction) decreased, the punch position is
shifted to the paper rear edge side.
Change when the adjustment value is increased
or decreased
Saddle paper lead When the adjustment value is
edge striking plate increased, the stapling
stop position (Up- position is shifted to the lead
down direction) edge of transported paper.
When the adjustment value is
decreased, the stapling
position is shifted to the rear
edge of transported paper.
Saddle paper lead When the adjustment value is
edge striking plate increased, the folding position
stop position (Up- is shifted to the lead edge of
down direction) transported paper.
When the adjustment value is
decreased, the folding
position is shifted to the rear
edge of transported paper.
F side paper When the adjustment value is
alignment plate stop increased, the alignment
position position is shifted to the
(F/R direction) center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
R side paper When the adjustment value is
alignment plate stop increased, the alignment
position position is shifted to the
(F/R direction) center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
Stapling position When the adjustment value is
(stapler stop increased, the distance
position) between the stapling position
(F/R direction) and the paper edge becomes
longer.
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
Change
when the
adjustment
value is
changed by 1
0.155mm
0.155mm
0.1441mm
0.2584mm
Change when
the adjustment
value is
changed by 1
0.2mm
0.2mm
0.2mm
0.2mm
0.2mm