Preparation Before Operation - Panasonic CS-A7BKP Service Manual

CS-A7BKP CU-A7BKP5 / CS-A7BKP CU-A7BKP6 / CS-A9BKP CU-A9BKP5 / CS-A9BKP CU-A9BKP6 / CS-A12BKP CU-A12BKP5 / CS-A12BKP CU-A12BKP6
NAME OF EACH PART
■ Remote Control
1
2
3
4
5
6
7
8
9
0
● Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
● Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.

PREPARATION BEFORE OPERATION

■ Indoor Unit
6
3
5
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
AUTO HEAT
4
Fit the air purifying filters in place
5
Insert the air filters
6
Close the front panel
■ Remote Control
– To set the current time
AUTO
ON
OFF
CHECK
1 Press 1.
2 Then press 2 to increase or decrease the time.
3 Press 1 again.
Set time at display will light up.
1 Signal Transmitter
2 Operation Display
3 Powerful Mode Operation Button
4 Room Temperature Setting Button
AUT UTO HEA HEAT COOL COOL DRY FAN DR AN
AUTO
5 Operation Mode Selection Button
ON
6 Economy Mode Operation Button
AUTO
OFF
FAN
TEMP
7 Auto Airflow Direction Button
OFF/ON
POWERFUL
!
8 ON-Timer Button
#
9 OFF-Timer Button
MODE ECONOMY SLEEP
AIR SWING $
0 Reset Point
AUTO MANUAL FAN SPEED
$
1 2 3
%
ON SET
! OFF/ON Button
^
OFF CANCEL
&
TIMER
*
@ Sleep Mode Operation Button
CHECK RESET CLOCK
(
# Fan Speed Selection Button
$ Manual Airflow Direction Selection Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
HOW TO OPERATE
1
2
4
■ To start the operation
COOL DRY FAN
AUTO ■ Setting Mode
AUTO
FAN
AIR SWING
MANUAL FAN SPEED
1 2 3
SET
CANCEL
2
TIMER
1
RESET CLOCK
(self-illuminating button)
(Press with fine-tipped object to clear the memory)
(self-illuminating button)
2
3
5
1
6
4
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
• Press 2 to select:-
Cooling Model
AUTO – Automatic Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Air Circulation Operation
Heat Pump Model
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
34
● How to Insert the Batteries
2
1
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
● About the batteries
• Can be used for approximately one year.
● Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
■ Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
• Recommended temperature:
Cooling Model Heat Pump Model
COOL – 26°C ~ 28°C
COOL – 26°C ~ 28°C
DRY – 1°C ~ 2°C DRY – 1°C ~ 2°C
lower than the
lower than the
room temperature
room temperature
HEAT – 20°C ~ 24°C
• During AUTO Operation, press 3 to select:-
• Operation with 2°C higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 2°C lower than the standard
temperature.
● Standard Temperature
Cooling Model
Indoor Standard
temperature Operation temperature
Cooling 25°C
23°C
Soft Dry 22°C
• Once the Automatic Operation is selected, the indoor
temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.
• After the operation mode has been selected, the
mode does not change.
Heat Pump Model
Indoor Standard
temperature Operation temperature
Cooling 25°C
23°C Soft Dry 22°C
20°C
Heating 21°C
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.