Preparation Before Operation - Panasonic CS-C18BKP Service Manual

CS-C18BKP CU-C18BKP5 / CS-C18BKP CU-C18BKP6 / CS-C24BKP CU-C24BKP5 / CS-C24BKP CU-C24BKP6
NAME OF EACH PART
Remote Control
1
2
ON
OFF
3
POWERFUL
4
5
6
7
8
9
0
Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.

PREPARATION BEFORE OPERATION

Indoor Unit
6
3
5 4
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
4
Fit the air purifying filters in place
5
Insert the air filters
6
Close the front panel
Remote Control
– To set the current time
AIR SWING
1
ON
OFF
RESET CLOCK
1 Press 1.
2 Then press 2 to increase or decrease the time.
3
Press 1 again.
Set time at display will light up.
1 Signal Transmitter
2 Operation Display
3 Powerful Mode Operation Button
4 Room Temperature Setting Button
AUT AUTOHEA HEAT COOL COOL DR DRY FAN AN
(self-illuminating button)
AUTO
AUTO
5 Operation Mode Selection Button
AUTO
FAN
6 Economy Mode Operation Button
TEMP
7 Vertical Airflow Direction Button
OFF/ON
!
8 ON-Timer Button
#
MODE ECONOMY SLEEP
9 OFF-Timer Button
AIR SWING $
FAN SPEED
$
0 Reset Point
1 2
3
%
(Press with fine-tipped object to clear the memory)
ON SET
^
! OFF/ON Button
OFF
CANCEL
&
TIMER
(self-illuminating button)
*
CHECK RESET CLOCK
@ Sleep Mode Operation Button
(
# Fan Speed Selection Button
$ Horizontal Airflow Direction Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
HOW TO OPERATE
1
2
To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
Setting Mode
• Press 2 to select:-
FAN SPEED
2 3
SET
CANCEL
2
TIMER
1
2
3
5
1
6
4
Cooling Model
AUTO – Automatic Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Air Circulation Operation
Heat Pump Model
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
30
How to Insert the Batteries
2
1
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
About the batteries
• Can be used for approximately one year.
Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
• Recommended temperature:
Cooling Model Heat Pump Model
COOL – 26°C ~ 28°C COOL – 26°C ~ 28°C
DRY – 1°C ~ 2°C
DRY – 1°C ~ 2°C
lower than the
lower than the
room temperature
room temperature
HEAT – 20°C ~ 24°C
• During AUTO Operation, press 3 to select:-
• Operation with 2°C higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 2°C lower than the standard
temperature.
Standard Temperature
Cooling Model
Standard
Indoor
temperature Operation temperature
Cooling 25°C
23°C Soft Dry 22°C
• Once the Automatic Operation is selected, the indoor
temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.
• After the operation mode has been selected, the
mode does not change.
Heat Pump Model
Indoor Standard
Operation
temperature temperature
Cooling 25°C
23°C Soft Dry 22°C
20°C Heating 21°C
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.