Subscribe to Our Youtube Channel
Related Manuals for Planet IFT-802T
Summary of Contents for Planet IFT-802T
- Page 1 10/100BASE-TX to 100BASE-FX Industrial Media Converter IFT-802T / IFT-802TS15 / IFT-805AT User's Manual...
-
Page 2: Fcc Warning
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred. - Page 3 Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 10/100BASE-TX 100BASE-FX Industrial Media Converter User's Manual For Models: IFT-802T, IFT-802TS15, IFT-805AT Revision: 1.1 (June, 2015) Part No: EM-IFT-80xT_v1.1 (2350-AH1140-001)
-
Page 4: Table Of Contents
Table Of Contents 1. Introduction ..............5 1.1 Package Contents ............5 1.2 How to Use This Manual ..........5 1.3 Product Features ............6 1.4 Product Specifications ..........7 2. Installation ..............10 2.1 Product Description ..........10 2.1.1 Media Converter Front Panel ......12 2.1.2 LED Indicators .......... -
Page 5: Introduction
1. Introduction 1.1 Package Contents Check your package for the following parts: ● 10/100BASE-TX to 100BASE-FX Industrial Media Converter x 1 ● User’s Manual x 1 ● DIN Rail Kit x 1 ● Wall Mount Kit x 1 ● Screws x 1 (set) If any of these are missing or damaged, please contact your dealer immediately;... -
Page 6: Product Features
1.3 Product Features Physical Port IFT-802T • 1-Port 10/100BASE-TX RJ45 • 1-Port 100BASE-FX interface for up to 2km (Multi-mode fiber 62.5/125μm / 50/125μm) IFT-802TS15 • 1-Port 10/100BASE-TX RJ45 • 1-Port 100BASE-FX interface for up to 15km (Single mode fiber 9/125μm) IFT-805AT •... -
Page 7: Product Specifications
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Supports packet size of up to 1522bytes • CSMA/CD protocol • Automatic source address learning and aging 1.4 Product Specifications Product IFT-802T IFT-802TS15 IFT-805AT Hardware Specifications 10/100BASE-TX 1 RJ45 Auto-MDI/MDI-X port Port... - Page 8 Weight 430g Installation DIN rail kit and wall-mount ear Maximum Frame Packet size of 1522bytes Size Back pressure for half duplex, IEEE 802.3x Flow Control pause frame for full duplex Enclosure IP-30 slim-type metal case System: • Power 1 (green) •...
- Page 9 • 200Mbps for full-duplex 10/100BASE-TX: • 2-pair UTP Cat. 3, 4, 5 (100 meters, max.) • EIA/TIA-568 100-ohm STP (100 meters, max.) 100BASE-FX: • IFT-802T: Multi-mode optic fiber 62.5/125μm / Network Cables 50/125μm (2km) • IFT-802TS15: Single mode optic fiber 9/125μm (15km) •...
-
Page 10: Installation
100BASE-FX SC interface and 100BASE-FX SFP slot. The fiber transmit distance of the IFT-802T can be 2km while that of the IFT-802TS15 is 15km and that of the IFT-805AT varies depending on SFP module. With Fast Ethernet SFP interface, the IFT-805AT is highly... - Page 11 reliable and flexible to extend the distance from 2km to 60km, depending on the MFB family Fast Ethernet SFP modules. MFB family Fast Ethernet SFP module comes with one of the following models. The following list the available modules for the IFT-805AT Fast Ethernet SFP Module List Model...
-
Page 12: Media Converter Front Panel
LNK/ACT LNK/ACT LNK/ACT 100Base-FX 100Base-FX 100BASE-FX LNK/ACT LNK/ACT LNK/ACT 10/100BASE-TX 10/100Base-TX 10/100Base-TX IFT-802T IFT-802TS15 IFT-805AT Figure 2-1 IFT- Figure 2-2 IFT- Figure 2-3 IFT- 802T Front Panel 802TS15 Front Panel 805AT Front Panel 2.1.2 LED Indicators System Color Function Green Lit: Indicates power 1 has power. - Page 13 10/100BASE-TX RJ45 Port Color Function Lit: Indicates TP port is successfully connecting to the network at 100Mbps. 10/100 Green Off: Indicates TP port is successfully connecting to the network at 10Mbps. Lit: Indicates the link through that port is successfully established.
-
Page 14: Media Converter Upper Panel
2.1.3 Media Converter Upper Panel The upper panel of the Industrial Media Converter consists one terminal block connector within two DC power inputs. Figure 2-4 shows the upper panel of the Industrial Media Converter. Figure 2-4 Industrial Media Converter Upper Panel. 2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Media Converter is used for two DC redundant inputs. -
Page 15: Wiring The Fault Alarm Contact
2. Tighten the wire-clamp screws for preventing the wires from loosening Power 1 Fault Power 2 The wire gauge for the terminal block should be in the range of 12 to 24 AWG. Note 2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. -
Page 16: Mounting Installation
Converter and make connections to it. Please read the following steps to perform the procedures in the order being presented. In the installation steps below, this Manual uses the IGS-801 (PLANET 8-port Industrial Gigabit Switch) as an example. However, the steps for Note... -
Page 17: Installing Din-Rail Mounting
2.2.1 Installing DIN-Rail Mounting Follow the steps below for the DIN-rail mounting of the Industrial Media Converter: Step 1: Screw the DIN-rail on the Industrial Media Converter. Step 2: Lightly slide the DIN-rail into the track. - Page 18 Step 3: Make sure the DIN-rail is tightly on the track. Step 4: To remove Industrial Media Converter from the track, lightly lift it up.
-
Page 19: Wall-Mount Plate Mounting
2.2.2 Wall-mount Plate Mounting To install the Industrial Media Converter on the wall, please follow the instructions described below: Step 1: Remove DIN-rail from Industrial Media Converter; loosen the screws to remove the DIN-rail. Step 2: Place the wall-mount plate on the rear panel of the Industrial Media Converter. -
Page 20: Applications
3. Applications In this section, how to install Industrial Media Converter and its installation points are described below: 3.1 Installation Steps Step 1: Unpack the Industrial Media Converter. Step 2: Screw DIN-rail on the Industrial Media Converter. Please refer to the DIN-rail Mounting section for DIN-rail installation if the DIN-rail is not screwed on the Industrial Media Converter. - Page 21 5 cable. Note Step 7: Insert the fiber cable from the IFT-802T / 802TS15 / 805AT to the fiber network. TX and RX must be paired at both ends. The optical port LED on the Industrial Media Converter will light up when the cable is connected with the network device.
-
Page 22: Media Converter Operation
4. Media Converter Operation 4.1 Learning When one packet comes in from any port, the Industrial Media Converter will record the source address, port number and the other related information in the address table. This information will be used to decide whether forwarding or filtering is for future packets. -
Page 23: Auto-Negotiation
The Industrial Media Converter scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the media converter attractive for connecting servers directly to the network, thereby increasing throughput and availability. -
Page 24: Troubleshooting
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Media Converter is not functioning properly, make sure the Industrial Media Converter was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Media Converter. - Page 25 Why the Industrial Media Converter doesn’t connect to the network Solution: Check per port LED on the Industrial Media Converter. Try another port on the Industrial Media Converter Make sure the cable is installed properly. And make sure the cable is the right type to turn off the power.
-
Page 26: Appendix A: Networking Connection
Appendix A: Networking Connection A.1 Media Converter’s RJ45 Pin Assignments 10/100Mbps, 10/100BASE-TX RJ45 Connector Pin Assignment MDI Media Dependent MDI-X Media Dependent Contact Interface Interface-Cross Tx + (transmit) Rx + (receive) Tx - (transmit) Rx - (receive) Rx + (receive) Tx + (transmit) 4, 5 Not used... -
Page 27: Fiber Optical Cable Connection Parameter
Straight Cable SIDE 1 SIDE 2 SIDE 1 1 2 3 4 5 6 7 8 1 = White/Orange 1 = White/Orange 2 = Orange 2 = Orange 3 = White/Green 3 = White/Green 4 = Blue 4 = Blue 5 = White/Blue 5 = White/Blue 1 2 3 4 5 6 7 8... -
Page 28: Ec Declaration Of Conformity
For the following equipment: *Type of Product: 10/100BASE-TX to 100BASE-FX Industrial Media Converter with Wide Operating Temperature *Model Number: IFT-802T / IFT-802TS15 / IFT-805AT * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address: 11F, No 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Need help?
Do you have a question about the IFT-802T and is the answer not in the manual?
Questions and answers