Subscribe to Our Youtube Channel
Related Manuals for Planet IGTP-2205AT
Summary of Contents for Planet IGTP-2205AT
- Page 1 Compact Industrial 2-Port 100/1000X SFP to 2-Port 10/100/1000T 802.3at PoE+ Media Converter IGTP-2205AT User's Manual...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Product Specifications ..................4 3. Hardware Introduction ................... 6 3.1 Three-View Diagram ................6 3.2 LED Definition: ..................8 3.3 Wiring the Power Inputs ................9 4. Hardware Installation ................... 10 4.1 DIN-rail Installation ................10 4.2 Wall Mounting .................. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Compact Industrial 100/1000X to 10/100/1000T 802.3at PoE+ Media Converter, IGTP-2205AT. In the following sections, the term “Industrial PoE+ Media Converter” means the IGTP-2205AT. Open the box of the Industrial PoE+ Media Converter and carefully unpack it. The... -
Page 4: Product Specifications
2. Product Specifications Model IGTP-2205AT Hardware Specifications 2 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with PoE Copper Port injector function 2 1000BASE-SX/LX/BX SFP interfaces SFP Port Compatible with 100BASE-FX SFP Back pressure for half duplex mode Flow Control IEEE 802.3x pause frame for full duplex mode... - Page 5 10/100/1000BASE-T: 2-pair UTP Cat. 3, 4, 5, 5e, 6 (maximum 100 meters) EIA/TIA-568 100-ohm STP (maximum 100 meters) Cables 100BASE-FX/1000BASE-SX/LX: Multi-mode: 50/125μm or 62.5/125μm optical fiber Single-mode: 9/125μm optical fiber Power Over Ethernet PoE Standard IEEE 802.3at Power over Ethernet Plus PoE Power Output 48~54V DC: 30 watts per port PoE Power Supply End-span Type Power Pin 1/2(+), 3/6(-) Assignment PoE Power Budget 60 watts Standards Conformance Regulatory FCC Part 15 Class A, CE Compliance IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet...
-
Page 6: Hardware Introduction
Top View Mounting Kit Side View Front View Side View Rear View LNK/ACT PoE-in-Use DIN-Rail Kit 100/1000X IGTP-2205AT Bottom View Mounting Kit Dimensions (W x D x H): 30 x 70 x 104 mm Figure 1: IGTP-2205AT Three-View Diagram... - Page 7 Front View LNK/ACT PoE-in-Use 100/1000X IGTP-2205AT Figure 2: IGTP-2205AT Front View...
-
Page 8: Led Definition
3.2 LED Definition: System Color Function Green Lights to indicate the Industrial PoE+ Media Converter has power. Green Lights to indicate the Industrial PoE+ Media Converter has power. 10/100/1000BASE-T Ports (Ports 1 to 2) Color Function Lit: Indicates that the Copper Port is successfully connecting to the network at 10/100/1000Mbps. -
Page 9: Wiring The Power Inputs
3.3 Wiring the Power Inputs The 4-contact terminal block connector on the top panel of Industrial PoE+ Media Converter is used for 48~54V DC power inputs. Please follow the steps below to insert the power wire. When performing any of the procedures like inserting the wires or tight- ening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock. -
Page 10: Hardware Installation
DIN rail and wall. Please read this chapter completely before continuing. This following pictures guide you to installing the device, and the device is not IGTP-2205AT. 4.1 DIN-rail Installation Figure 3: DIN-rail Mounting Place the bracket on the back of the device and with the given 3 screws, tighten them. Slide the device with the bracket mounted through the DIN-rail to finish the... -
Page 11: Wall Mounting
4.2 Wall Mounting Figure 4: Wall Mounting Place both mounting plates on the back of the device, and tighten them with the given screws. Then put the device with the plates mounted on the wall, and screw them to finish the installation. 4.3 Side Wall Mounting Figure 5: Wall Mounting Place the two mounting plates on the bottom of the device, and tighten them with the given screws. -
Page 12: Grounding The Device
4.4 Grounding the Device Users MUST complete grounding wired with power cord adapter or power supply source should be connected to a socket outlet with an earthing connection; otherwise, a sudden lightning could cause fatal damage to the device. 1 2 3 4 DC Input Range: 48-54V , 2A max. -
Page 13: Fiber And Poe Installation
If there is any IEEE 802.3at/802.3af devices needed to power on, the IGTP-2205AT can provide you with a way to supply power for this Ethernet device conveniently and easily. The IGTP-2205AT needs DC 48-54V input to inject the DC power into the pin of the twisted pair cable (Pins 1, 2, 3 and 6). Wi-Fi AP... -
Page 14: Customer Support
Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.
Need help?
Do you have a question about the IGTP-2205AT and is the answer not in the manual?
Questions and answers