Automatic Arming; Entry And Exit Delay Options - DSC Envoy NT9010 Installation Manual

2.2.6 Automatic
Arming
2.2.7 Entry and Exit
Delay Options
Se cti o n 2. 2: C ha ng i ng H o w th e NT 90 10 Wo rk s For Us er s
Arm/Disarm Bell Squawk. . . . . . . . . . . . . . . . . . . . . . . . . .Section [014], Option [1]
WLS Key Does Not Use Access Codes . . . . . . . . . . . . . . . .Section [017], Option [1]
Bell Squawk on Away Arming . . . . . . . . . . . . . . . . . . . . . .Section [017], Option [8]
Opening After Alarm Keypad Ringback . . . . . . . . . . . . . . .Section [381], Option [1]
Opening After Alarm Bell Ringback . . . . . . . . . . . . . . . . . .Section [381], Option [2]
Closing Confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [381], Option [4
You can program the system to automatically arm at a specific time every day. Three items
must be enabled in order to activate the auto arming function:
1. The correct time of day must be programmed. For instructions on programming the
time and date, see the NT9010 User's Guide ("Setting the Time and Date").
2. Enter [ ][6][Master Code][2] to enable (three keypad beeps) or disable (one long
beep) the auto-arm feature.
3. Program the auto-arm time using the [ ][6][Master Code][3] command.
When the internal system clock matches the programmed auto arm time, the system will
check its status. If the system is armed, the NT9010 will do nothing until the programmed
auto-arm time for the next day, when it will check again.
If the system is disarmed at the auto-arm time, the NT9010 control unit will sound the key-
pad buzzer for one minute. This is the auto arm pre-alert period.
If the Bell Squawk During Auto Arm option is enabled, the bell will squawk while the
system is auto-arming in order to notify anyone on the premises that the system is being
armed.
If a valid access code is entered during the auto arm pre-alert period, automatic arming will
be cancelled. If automatic arming is cancelled by a user, the system will send the Auto Arm
Reporting Code to the central station.
NOTE:
The Maintenance code cannot be used to cancel automatic arming.
If no code is entered during the auto-arm prealert, the system will auto-arm. If a zone is vio-
lated when the system arms, the system will transmit a Partial Closing Reporting Code
(if programmed), to indicate the system was not secure. If the zone is restored, the NT9010
will arm the zone and add it back into the system.
Program Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . [ ][6][Master Code][1]
Enable Auto Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [ ][6][Master Code][2]
Program Auto Arm Time . . . . . . . . . . . . . . . . . . . . . . . . . . . [ ][6][Master Code][3]
Partial Closing Reporting Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [343]
Auto Arm Cancellation Reporting Code . . . . . . . . . . . . . . . . . . . . . . Section [348]
Bell Squawk During Auto Arm . . . . . . . . . . . . . . . . . . . . .Section [014], Option [2]
Upon arming, the system will begin the exit delay. If Audible Exit Delay is enabled the key-
pad will beep every second until the exit delay expires. The keypad will beep rapidly for the
last 10 seconds of exit delay to warn the user the system is about to arm.
Users can restart the exit delay one time while it is counting down by pressing the Away key.
The system will not log the user who re-started the exit delay, unless the Quick Arming Dis-
abled/Function Keys Require Code option is turned on (section [015], option [4]).
2 3