Table Of Contents - ProBoat Recoil PRB08022 Owner's Manual

Water-Resistant Boat with Waterproof Electronics
Your new Horizon Hobby boat has been designed and
built with a combination of waterproof and water-resistant
components to allow you to operate the product in calm,
fresh water conditions.
While the entire boat is highly water-resistant, it is not
completely waterproof and your boat should NOT be treated
like a submarine. The various electronic components used
in the boat, such as the ESC, servo(s) and receiver are
waterproof, however, most of the mechanical components are
water-resistant and require additional maintenance after use.
Metal parts, including the bearings, pins, screws and nuts,
propeller, rudder, rudder mounts, prop struts, as well as
General Precautions
• Read the WET CONDITIONS MAINTENANCE
procedures and make sure that you have all the tools
you will need to properly maintain your boat.
• Not all batteries can be used in wet conditions. Consult
the battery manufacturer before use. Caution should be
taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult
your transmitter's manual or the manufacturer before
operation.
• Never operate your transmitter or boat when lightning is
present.
• Salt water is very conductive and highly corrosive. If
you choose to run your boat in salt water, immediately
rinse the boat in fresh water after each use. Operating
your boat in salt water is at the sole discretion of the
modeler.
Wet Conditions Maintenance
• Drain any water that has collected in the hull by
removing the drain plug or canopy and tilting the boat in
the appropriate direction to drain the water.

Table of Contents

Transmitter Controls ...................................................... 4
Transmitter Battery Installation .................................... 4
Battery Charger .............................................................. 4
Getting Started ............................................................... 5
Range Check ................................................................... 5
Boating Tips ................................................................... 6
Self-Righting ................................................................. 6
When you are Finished ................................................. 6
Maintenance ................................................................... 7
Drivetrain Lubrication..................................................... 7
Propeller Service ........................................................... 7
Rudder Service .............................................................. 7
Rudder Trim .................................................................... 8
Water Cooling System .................................................. 8
Binding ........................................................................... 8
Transmitter Calibration.................................................. 9
Failsafe ............................................................................ 9
Low Voltage Cutoff......................................................... 9
Troubleshooting Guide ............................................... 10
LIMITED WARRANTY ....................................................11
Warranty and Service Contact Information ............... 12
Compliance Information for the European Union .... 12
Replacement Parts ....................................................... 43
Optional Parts .............................................................. 43
Recoil ® 26
the contacts in the electrical cables, will be susceptible
to corrosion if additional maintenance is not performed
after running in wet conditions. To maximize the long-
term performance of your boat and to keep the warranty
intact, the procedures described in the WET CONDITIONS
MAINTENANCE section must be performed regularly.
CAUTION: Failure to exercise caution while using
this product and complying with the following
precautions could result in product malfunction and/or void
the warranty.
CAUTION: Always keep hands, fingers, tools and
any loose or hanging objects away from rotating
parts.
• Remove the battery pack(s) and dry the contacts. If
you have an air compressor or a can of compressed air,
blow out any water that may be inside the recessed
connector housings.
• Remove all moving parts. Dry and lubricate parts after
every 30 minutes of operation or if the boat becomes
submerged.
NOTICE: Never use a pressure washer to clean your boat.
• Use an air compressor or a can of compressed air to
dry the boat and help remove any water that may have
gotten into small crevices or corners.
• Spray the bearings, fasteners and other metal parts with
a water-displacing light oil or lubricant.
• Let the boat air dry before you store it. Water (and oil)
may continue to drip for a few hours.
Specifications
Length 26 in (660.4mm)
Beam (width) 7.9 in (200mm)
Hull Material Blow-Molded ABS Plastic
Dynamite
Motor
marine motor
Dynamite
ESC
water-cooled
ECX
Transmitter
ECX 2.4GHz Receiver, Waterproof
Receiver
11.1V 3200mAh 3S 30C LiPo w
Batteries
EC3™ connector
(4) AA batteries (sold separately) are
required to operate the transmitter.
26in (660.4mm)
7.9in
(200mm)
®
Outrunner BL
®
30-amp brushless,
®
2.4GHz Transmitter
EN
EN EN
3