GE NetworX NX-6V2 Installation And Startup page 24

70
Location 70 contains the digits for a 4+2 format that will be sent if "Aux Power Overcurrent Reporting" is enabled. Segments 1 & 2
contain the digits of the "Aux Power Overcurrent Reporting". Segments 3 & 4 contain the digits of the "Aux Power Overcurrent
Restore". (Box on pg 23.)
71
Location 71 contains the digits for a 4+2 format that will be sent if siren supervision reporting is enabled. Segments 1 & 2 contain the
digits of the "Bell Tamper Reporting". Segments 3 & 4 contain the digits of the "Bell Tamper Restore". (Box on pg 23.)
72
Location 72 contains the digits for a 4+2 format that will be sent if "Telephone Line Cut Reporting" is enabled. Segments 1 & 2 contain
the digits of the "Telephone Line Cut Reporting". Segments 3 & 4 contain the digits of the "Telephone Line Cut Restore". (Box on pg
23.)
73
Location 73 contains the digits for a 4+2 format that will be sent if "Ground Fault Reporting" is enabled, and the NX-870E is installed.
Segments 1 & 2 contain the digits of the "Ground Fault Reporting". Segments 3 & 4 contain the digits of the "Ground Fault Restore".
(Box on pg 23.)
74
Location 74 contains the digits for a 4+2 format that will be sent if "Expander Trouble Reporting" is enabled. Segments 1 & 2 contain
the digits of the "Expander Trouble Reporting". Segments 3 & 4 contain the digits of the "Expander Trouble Restore". (Box on pg 23.)
75
Location 75 contains the digits for a 4+2 format that will be sent if the "Fail To Communicate Reporting" is enabled. (Box on pg 23.)
76
Location 76 contains the digits for a 4+2 format if the "Log Full Reporting" is enabled. (Box on pg 23.)
77
Location 77 contains the digit of a 4+2 format if the "Opening Reporting" is enabled. (Box on pg 23.)
Segment 1 = Partition 1
78
Location 78 contains the digit of a 4+2 format if the "Closing Reporting" is enabled. (Box on pg 23.)
Segment 1 = Partition 1
79
Location 79 contains the digits for a 4+2 format that will be sent if the "Autotest" or "Manual Test" is enabled. (Box on pg 23.)
80
Location 80 contains the digits for a 4+2 format that will be sent if "Recent Closing" and/or "Exit Error Reporting" is enabled. Segment
1 contains the digit for the "Recent Closing Reporting". Segment 2 contains the digit for the "Exit Error Reporting". (Box on pg 23.)
81
Location 81 contains the digits for a 4+2 format that will be sent if "Start / End Programming Reporting" is enabled. Segment 1
contains the digit for the "Start Program Reporting". Segment 2 contains the digit for the "Start Program Reporting". Segment 3
contains the digit for the "End Program Reporting". Segment 4 contains the digit for the "End Program Reporting". (Box on pg 23.)
82
Location 82 contains the digits for a 4+2 format that will be sent if "End Downloading Reporting" is enabled. Segments 1 and 2 are
Reserved. Segment 3 contains the digit of the "End Download Reporting". Segment 4 contains the digit of the "End Download
Reporting". (Box on pg 23.) Note: A start download report will be sent to the internal event log.
83
Location 83 contains the digit for a 4+2 format that will be sent if "Cancel Reporting" is enabled. Segment 1 contains the digit for the
"Cancel Communicator Reporting". (Box on pg 23.)
84-87
24
AUX POWER OVERCURRENT / RESTORE COMM CODE
BELL TAMPER / RESTORE COMMUNICATOR CODE
TELEPHONE LINE CUT / RESTORE COMM CODE
GROUND FAULT / RESTORE COMMUNICATOR CODE
EXPANDER TROUBLE / RESTORE COMM CODE
FAIL TO COMMUNICATE COMMUNICATOR CODE
LOG FULL COMMUNICATOR CODE
OPENING COMMUNICATOR CODE
Segment 2 = Partition 2
CLOSING COMMUNICATOR CODE
Segment 2 = Partition 2
AUTOTEST COMMUNICATOR CODE
RECENT CLOSING & EXIT ERROR COMM CODE
START PROGRAM & END PROGRAM COMM CODES
END DOWNLOAD COMMUNICATOR CODE
CANCEL COMMUNICATOR CODE
RESERVED
4 ............ numerical
4 ............ numerical
4 ............ numerical
4 ............ numerical
4 ............ numerical
2 ............ numerical
2 ............ numerical
2 ............ numerical
2 ............ numerical
2 ............ numerical
2 ............ numerical
4 ............ numerical
4 ............ numerical
1 ............ numerical
NX-6V2 Control