Optional Mantel Installation - Comfort Glow CF26PR Owner's Operation And Installation Manual

INSTALLATION
Continued
MANTEL CLEARANCES FOR
BUILT-IN INSTALLATION
If placing mantel above built-in fireplace,
you must meet minimum clearance between
mantel shelf and top of fireplace opening.
If your installation does not meet the mini-
mum clearances in Figure 9, you must:
• raise the mantel to an acceptable height,
OR
• remove the mantel.
Note: All vertical
10"
measurements
are from top of
8"
fireplace
6"
opening to
2 1 /2"
bottom of
mantel shelf.
Minimum Non-
Combustible
Material
Figure 9 - Minimum Mantel Clearances
for Built-In Installation
REMOVING BRICK LINER
RETAINER
1. Using Phillips screw driver, remove 2
screws attaching brick liner retainers to
vertical sides.
2. Remove brick liner retainers and discard.
Replace 2 screws into vertical sides.
ASSEMBLING BRASS TRIM
(Brass trim shipped with mantel)
1. Remove packaging from three pieces
of brass trim.
2. Locate two adjusting plates with set
screws, and two shims in the hardware
packet.
3. Align shim under adjusting plate as
shown in Figure 10.
4. Slide one end of adjusting plate/shim
in slot on mitered edge of top brass trim
(see Figure 10).
105442
5. Slide other end of adjusting plate/shim
in slot on mitered edge of side brass
trim (see Figure 10).
6. While firmly holding edges of brass trim
together, tighten both set screws on the
adjusting plate with slotted screwdriver.
7. Repeat steps 1 through 6 for other corner.
8. Set brass assembly aside for later in-
stallation.
Set Screws
Mantel Shelf
Adjusting
Plate
Figure 10 - Assembling Brass Trim
OPTIONAL MANTEL
INSTALLATION
Note: Refer to instructions provided with
the mantel for assembly instructions. Refer
to instructions below for system installa-
tion. If using blower accessory (see Acces-
sories, page 28), see installation instruc-
tions on pages 10 and 11.
1. Choose location for fireplace and in-
stall gas supply line.
2. Remove screen from fireplace by remov-
ing screws in each end of screen rod (see
Figure 11). Hold screen rod cover while
removing five hex head screws under-
neath hood (see Figure 12). Carefully lift
and pull out hood (see Figure 13).
3. Assemble brass trim kit. See Assem-
bling Brass Trim, column 1.
4. Place brass trim on the shoulder screws
located on the side and top of the fireplace.
Firmly snap the brass trim over the shoul-
der screws on fireplace (see Figure 14).
5. Place mantel base close to wall in de-
sired fireplace location.
6. Install gas line. See Connecting To Gas
Supply, page 12
7. Carefully place fireplace on mantel base
and center left to right. Check for gas leaks.
See Checking Gas Connections, page 14.
8. Refer to instructions provided with the
mantel for permanent attachment to wall.
9. Slide mantel around fireplace. Be care-
ful not to damage wall or mantel.
OWNER'S MANUAL
Top
Slot
Brass
Trim
Mitered
Shim
Edge
Side
Brass
Slot
Trim
9
10. Adjust assembly to remove any gaps.
From back side of fireplace, attach two
2" wood screws through base mount-
ing blocks attached to bottom sides of
mantel into base (see instructions pro-
vided with mantel).
11. Attach remaining two 3" wood screws
from hardware pack through openings
inside of fireplace sides into the mantel.
See Figure 13 for screw hole location.
Figure 11 - Removing Screen
Screw
Figure 12 - Removing Hood Screws
Figure 13 - Removing Hood
Assembled
Brass Trim
Figure 14 - Attaching Brass Trim to Fireplace
Hood
Screen
Rod
Cover
Mantel Screw
Location
Shoulder
Screws
Continued