Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for moon Neo 250i
Summary of Contents for moon Neo 250i
- Page 1 Owner’s Manual Series 250i Integrated Amplifier...
-
Page 3: Important Safety Instructions
250i Integrated Amplifier Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves or another apparatus that produces heat. - Page 4 To prevent shock hazard, all three connections must ALWAYS be used. Connect the MOON 250i only to an AC source of the proper voltage; Both the shipping box and rear panel serial number label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty AC extension cords are NOT recommended for use with this product.
-
Page 5: Table Of Contents
250i Integrated Amplifier Table of Contents Introduction ............ 6 Unpacking............7 Installation & Placement ........7 Front Panel Controls ......... 8 Rear Panel Connections ........9 SimLink™ ............10 Operating the 250i ..........10 Remote Control Operation ........11 Specifications ..........13 www.simaudio.com Simaudio Ltd., 1345 Newton Road Boucherville, Quebec J4B 5H2 CANADA Date Code: 20140717 ____________________________________________________________________________________... -
Page 6: Introduction
MOON capturing these elusive qualities. integrated amplifiers are so musically satisfying. The information contained in this manual is subject The performance of your 250i will continue to to change without notice. -
Page 7: Unpacking
250i Integrated Amplifier Unpacking The Nēo 250i integrated amplifier should be removed from its box with care. The following accessories should be included inside the box with your integrated amplifier: AC power cable ‘CRM-2’ remote control with two ‘AA’ batteries This owner’s manual Warranty and product registration information (USA and Canada only) -
Page 8: Front Panel Controls
250i Integrated Amplifier Front Panel Controls Figure 1: Nēo 250i Front panel The front panel will look similar to Figure 1 (above). The “Spk off” button turns off the output signal only The remote control sensor is located directly to the to the loudspeakers connected to the Nēo 250i. -
Page 9: Rear Panel Connections
1/8” mini jacks. Please refer to the next section entitled SimLink™ for more details. Next, there’s a * Please speak with your MOON Authorized Retailer about the benefits of high quality cables for your system, and 1/8” mini-jack input for use with aftermarket superior quality AC wall outlet. -
Page 10: Simlink
Please Turning on your MOON 250i for the first time Prior to turning the amplifier on for the first time, illuminated, your 250i is in standby mode. Next, make sure that every cable is properly connected to briefly press the push button labeled “Standby”... -
Page 11: Remote Control Operation
The Nēo 250i Integrated Amplifier uses the ‘CRM-2’ full-function remote control (figure 4). It operates on the Philips RC-5 communication protocol and is can be used with other Simaudio MOON components. The ‘CRM-2’ remote uses two AA batteries (included). To install them, simply slide the back plate off in the direction of the arrow;... - Page 12 250i Integrated Amplifier Remote operation with multiple MOON components Figure 4: Remote Operation with SimLink™ In figure 4 we have a 180 “MiND” Music Streamer jack cable. When you launch the MiND App on your and a Nēo 250i Integrated Amplifier connected smart device and select this system’s ZONE, both...
-
Page 13: Specifications
250i Integrated Amplifier Specifications Configuration ..........Stereo Power Supply Transformer ......320VA Power Supply Capacitance ......20,000µF Class Of Operation - Amplifier ......Class A/B Single-ended inputs ........5 (RCA) Mini-jack input ..........1 (1/8”) Input Sensitivity ..........370mV – 3.0V RMS Input Impedance ..........
Need help?
Do you have a question about the Neo 250i and is the answer not in the manual?
Questions and answers