How To Use The Front Panel; Program Start; Programme End; A.soak - Hisense HWFR6510 User's Operation Manual

Notes:
. .
Keep detergents and additives in a safe, dry place out of the reach of children.
Liquid detergents can be used for programmes with prewash. However, in this case
.
a powder detergent must be used for the main wash.
Do not use liquid detergents when activating the " Start Delay " function (if available
.
on your washing machine).
To prevent dispensing problems when using highly concentrated powder and liquid
detergents, use the special detergent ball or bag supplied with the detergent and
.
place it directly inside the drum.
When using descaling agents, bleaches or dyes, make sure that they are suitable
for washing machines. Descalers could contain compounds that can damage parts
. .
of your washing machine.
Do not use any solvents in the washing machine (e.g. turpentine, benzine).
. .
If you use starch powder, proceed as follows:
Wash your laundry using the desired wash programme.
.
Prepare the starch solution according to the starch manufacturer's instructions.
Select the " Rinse+ Spin" programme, reduce the speed to 800 rpm and start the
.
programme.
Pull out the detergent drawer until you can see about 3 cm of the main wash
.
chamber
.
Pour the starch solution into the main wash chamber
.
into the detergent drawer.
If there are starch residues in the detergent drawer when the programme has
finished, clean the main wash chamber.

HOW TO USE THE FRONT PANEL

.

Program Start

.
Open the tap, add detergent, load the drum and close the door.
Turn the selector to choose the right wash cycle for the type of fabric you are
washing. These program (depends on model availability) are including cotton,
Synthetics, Mix, Quick, Silk/Delicate, Wool, Underwear, Big Items, Down Jacket,
.
95 Antibacterial, Drum Clean, Rinse+Spin, Spin, and Daily Wash.
You can setup manually the spin time and speed, extra rinse, wash time,
.
Temperature, rinse hold and delay
You are also able to save these setting for your convenience by using the smart
. .
I.Program function (please refer to this section for setting it up).
Ppress the "Start/Pause" button to start the
The status indicator bar shows the current programme phase, running from left to
.
right through such as A.Soak, Wash, Rinse, Rinse hold, and Spin.
The time display shows the remaining of the programme time.
9
while the water is running
.
program.

Programme End

.
All the lights of the programme sequence indicator are off, and the " Door open"
indication in the status bar lights up.Turn the programme selector to the "Off"
. .
position.
Close the water tap.
.
Open the door and unload the machine .
Leave the door open to allow the drum to dry.
Notes: You can open the door only when the Door Open light on .
SELECT ANY DESIRED PUSH BUTTON OPTION:
Press the selected push button option once, the current value is displayed. By
pressing the button repeatedly, it will display the values in sequence. By pressing
the button of the desired option, the respective indicator lights up.
When the combination of programme and additional options is not possible, the
indication lights switch off automatically. Unsuitable combinations of options are
deselected automatically.
The picture is only for reference and it might be different on each model

A.Soak

Add the powder detergent or the sterilized powder agent in the pre-wash
chamber. Recommended for laundry which is heavily soiled or which should be
sterilized, the duration can be chose to be 28 minutes, 38 minutes or 48 minutes.
During the 18 minutes from the beginning of the cycle, the drum is turning, then it
will stop and the laundry is soaked. In the end of cycle, the water in the tub is
drained off.

Temp

On selecting a programme, a predefined temperature is displayed. Press " Temp." to
set a desired temperature.
10