Water Tap Closed" Indication Lights Up; Error Code; If A Failure Code Between "F02" And "F35" Appears On The Display; If Failure Code "Fa" Appears On The Display - Hisense HWFR6510 User's Operation Manual

"Water tap closed" indication lights up

The appliance has none or insufficient water supply. For models with remaining time
display, "FH" appears on the display. The "Start/Pause" indicator flashes.
.
Check whether:
The water tap status light bar is off and it is fully open and there is sufficient
. .
water supply pressure.
Kinks are present in the water hose.
The mesh filters of the water supply are blocked(see "Care and
.
Maintenance "/"Mesh Filters for Water Connection ").
The water pipingis frozen up.
After the problem has been removed, restart the programme by pressing
"Start/Pause" again. If the fault occurs again, contact After-Sales Service (see

"After-Sales Service").

"Clean pump" indication in status light bar lights up
Waste water is not being pumped out. The "Clean pump " indication lights up in
status light bar. For models that support the remaining time display, "FP" appears on
the display.
The washing machine stops in the appropriate programme step. Unplug the
appliance.
. .
Check whether:
Kinks are present in the drain hose
The pump or the filter is blocked (follow the instruction in "Removing the
Filter" section).
IMPORTANT:
Ensure that the water has cooled before draining the appliance. In addition,
. .
place a large container in front of the filterto collect water flowing from the filter.
The drain hose is frozen up
Plug in the appliance again.
Select and start the "Drain " programme (depend on the model availability) or push
the "Reset " button for at least 3 seconds and restart the desired programme. If the
fault occurs again, please contact After-Sales Service (see "After-Sales Service").

Error code

The appliance stops during the programme.
For models with a remaining time display, a failure code between "F02" and "F35",
"FA" or "Fod " appears on the display. For models without a display, the programme
sequence indicator will show the failure code by the combination of LED lights.
.

If a failure code between "F02" and "F35" appears on the display:

Select and start the "Drain " programme (depend on the model availability)
.
or push the "Reset " button for at least 3 seconds.
Then select and start the desired programme again. If the fault persists,
unplug the appliance and contact After-Sales Service (see "AfterSales
Service").
19
.

If failure code "FA" appears on the display

Switch the appliance off, pull out the mains plug and turn the water tap
off.Place a large container in front of the filterto receive water flowing from
the filter. Tilt the appliance forward carefully to allow the collected water to
flow out from the bottom of the appliance.Direct theflowing water into the
container flowing water into the container you have placed in front of the filter.
You can use apiece of cloth to absorb any spilled water.
. .
Then:
Connect the appliance to the electrical supply.
Turn the water tap on (if water immediately flows into the appliance again,
without the appliance being started, there is a failure. Turn off the tap and
notify After Sales Service)
Select and start the desired programme again. If the failure occurs again, unplug the
appliance and contact our After Sales Service (see "After Sales Service").

If failure code "Fod" appears on the display

Too much foam interrupted the washing programme. Avoid excessive detergent
. .
dosing during adding detergent.
Select and start the "Rinse & Spin" programme.
Afterwards, select and start the desired programme again, using less
detergent. If the fault persists, unplug the appliance and contact our After
Sales Service.
AFTER-SALES SERVICE
.
Before contacting After-Sales Service:
Try to remedy troubleshoot the problem yourself(see "Troubleshooting
. .
Guide").
Restart the programme to check whether the problem has solved itself.
If the washing machine continues to function incorrectly, call After -Sales
Service.
20