While Operating - Toro Workman
3300–D Operator's Manual

• Check the safety interlock system daily for proper
operation. If a switch should malfunction, replace the
switch before operating machine. After every two years,
replace the interlock switches in the safety system,
whether they are working properly or not.

While Operating

• Operator and passenger should use seat belts and
remain seated whenever the vehicle is in motion.
Operator should keep both hands on steering wheel,
whenever possible and passenger should use hand holds
provided. Keep arms and legs within the vehicle body at
all times. Never carry passengers in the box or on
attachments. Remember your passenger may not be
expecting you to brake or turn and may not be ready.
• Never overload your vehicle. Name plate (located under
middle of dash) shows load limits for vehicle. Never
overfill attachments or exceed the vehicle maximum
GVW.
• When starting the engine:
– Sit on operator's seat and ensure parking brake is
engaged.
– Disengage PTO (if so equipped) and return hand
throttle lever to OFF position (if so equipped).
Note: On models 07362TC and 07364TC only, make sure
hydraulic lift lever is in the NEUTRAL position.
– Move shift lever to NEUTRAL and depress clutch
pedal.
– Keep foot off accelerator pedal.
– Turn ignition key to ON, hold glow plug switch ON.
(Maximum 30 seconds).
– Turn ignition key to START.
• Using the machine demands attention. Failure to
operate vehicle safely may result in an accident, tip over
of vehicle and serious injury or death. Drive carefully.
To prevent tipping or loss of control:
– Use extreme caution, reduce speed and maintain a
safe distance around sand traps, ditches, creeks,
ramps, any unfamiliar areas or other hazards.
– Watch for holes or other hidden hazards.
– Use caution when operating vehicle on a steep
slope. Normally travel straight up and down slopes.
Reduce speed when making sharp turns or when
turning on hillsides. Avoid turning on hillsides
whenever possible.
– Use extra caution when operating vehicle on wet
surfaces, at higher speeds or with a full load.
Stopping time will increase with a full load. Shift
into a lower gear before starting up or down a hill.
– When loading bed, distribute load evenly. Use extra
caution if the load exceeds the dimensions of the
vehicle/bed. Operate vehicle with extra caution
when handling off–center loads that cannot be
centered. Keep loads balanced and secure to prevent
them from shifting.
– Avoid sudden stops and starts. Do not go from
reverse to forward or forward to reverse without
first coming to a complete stop.
– Do not attempt sharp turns or abrupt maneuvers or
other unsafe driving actions that may cause a loss of
vehicle control.
– Do not pass another vehicle traveling in the same
direction at intersections, blind spots, or at other
dangerous locations.
– When dumping, do not let anyone stand behind
vehicle and do not dump load on any one's feet.
Release tailgate latches from side of box, not from
behind.
– Keep all bystanders away. Before backing up, look
to the rear and assure no one is behind the vehicle.
Back up slowly.
– Watch out for traffic when near or crossing roads.
Always yield the right of way to pedestrians and
other vehicles. This vehicle is not designed for use
on streets or highways. Always signal your turns or
stop early enough so other persons know what you
plan to do. Obey all traffic rules and regulations.
– Never operate vehicle in or near an area where there
is dust or fumes in the air which are explosive. The
electrical and exhaust systems of the vehicle can
produce sparks capable of igniting explosive
materials.
– Always watch out for and avoid low over hangs
such as tree limbs, door jambs, over head walkways,
etc. Make sure there is enough room over head to
easily clear the vehicle and your head.
– If ever unsure about safe operation, STOP WORK
and ask your supervisor.
• Do not touch engine, transaxle, radiator, muffler or
muffler manifold while engine is running or soon after
it has stopped because these areas may be hot enough to
cause burns.
• If the machine ever vibrates abnormally, stop
immediately, turn engine off, wait for all motion to stop
and inspect for damage. Repair all damage before
resuming operation.
• Before getting off the seat:
– Stop movement of the machine.
– Lower bed.
– Shut engine off and wait for all movement to stop.
5