Furuno FI-70 Operator's Manual page 76

APPENDIX 1 MENU TREE
1 (Continued from previous page)
Engine Setup
Scale Range
IF-NMEAFI
I/O Setup
Data Source
Data Calibration
Demo Mode (OFF, ON)
Diagnostic (OFF, Self Test, Keyboard Test, Screen Test)
Restore Factory Default
Language (English, Francais, Espanol, Deutsch, Italiano, Potugues, Dansk, Svenska, Norsk, Suomi)
Units
AP-2
Number of Engine (1 to 3, 1)
Engine Assign (1 to 4, 1) Where [Number of Engine] is set to [1]
Engine PORT (1 to 4, 1) Where [Number of Engine] is set to [2] or [3]
Engine STBD (1 to 4, 2) Where [Number of Engine] is set to [2] or [3]
Engine Center (1 to 4, 3) Where [Number of Engine] is set to [3]
Engine Refresh
Speed (0-20kn, 0-40kn, 0-80kn)
Engine RPM (0-4×1000rpm, 0-6×1000rpm, 0-8×1000rpm)
Boost (0-30psi, 0-70psi, 0-150psi, 0-360psi, 0-440psi)
Eng. Temp. (150-250°F, 120-300°F)
Oil Press. (0-30psi, 0-70psi, 0-150psi, 0-360psi, 0-440psi)
Oil Temp. (150-250°F, 120-300°F)
Coolant P (0-30psi, 0-70psi, 0-150psi, 0-360psi, 0-440psi)
Gear Oil P (0-30psi, 0-70psi, 0-150psi, 0-360psi, 0-440psi)
Gear Oil T (150-250°F, 120-300°F)
Voltage (8-16V, 16-32V)
Select IF
Category (Wind, ST800/ST850, Fuel, Fresh Water, Waste Water, Live Well, Oil,
Black Water)
Resistance Full (0 to 500ohm, 33.5ohm)
Resistance Mid (0 to 500ohm, 103.00ohm)
Resistance Empty (0 to 500ohm, 240.00ohm)
Capacity (0 to 2650gal)
IF-NMEAFI Test
Refresh
Incoming PGN
Device List
CAN Bus Refresh (NMEA2000 Refresh)
Wiring Info
Position
Heading
STW
SOG
Navigation
Depth
W Temp.
Wind
AIS
Tank1 to Tank6
Adjust(STW) (0.30 to 2.50, 1.00)
Wind Damping (0s to 12s, 3s)
Adjust(W Speed) (0.30 to 2.50, 1.00)
W Angle Response (0s to 12s, 4s)
Offset(W Angle) (180° to P179°, 0°)
Offset(HDG) (180° to W179°, 0°)
Offset(Depth) (-327.8ft to +327.8ft, 0.0ft)
Offset(W Temp.) (-179.8°F to 179.8°F, 0.0°F)
Depth (m, ft, fm, PB)
Speed (kn, km/h, MPH)
Distance (NM, km, SM, NM,yd, NM,m, km,m, SM,yd)
Wind Speed (kn, km/h, MPH, m/s)
Temp (°C, °F)
Atmos. Press. (hPa, mbar)
Engine Press. (kPa, bar, psi)